No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 9800 V100 Configuration Guide 03

This document introduces service configuration process for OSN 9800.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Example: Configuring Transparently Transmitted Point-to-Point E-Line Services

Configuration Example: Configuring Transparently Transmitted Point-to-Point E-Line Services

This topic uses a transparently transmitted point-to-point E-Line service as an example to describe how to configure Ethernet services according to the network plan.

Networking Diagram

This topic describes the NE networking.

On the network shown in Figure 3-27, NE1 is located at the edge of the backhaul network and needs to transparently transmit Ethernet services from the NodeB to NE2.

To meet the requirement, you are advised to configure transparently transmitted point-to-point E-Line services.

Figure 3-27 Networking diagram (transparently transmitted point-to-point E-Line services)

Service Planning

This topic describes the service planning information about the point-to-point transparently transmitted E-Line services.

Table 3-16 describes the planning for Ethernet port parameters.

Table 3-16 Parameters of Ethernet ports
Item Value in This Example Planning Guidelines
Encapsulation Type Null For a port that carries transparently transmitted point-to-point services, this parameter takes the fixed value of Null.
Working Mode Auto-Negotiation
  • In this example, the GE port on the NodeB works in auto-negotiation mode. Therefore, the peer GE port must also work in auto-negotiation mode. If the peer Ethernet port works in another mode, the local Ethernet port must work in a consistent mode.
  • The working modes of the Ethernet ports within the backhaul network are uniformly planned as auto-negotiation.
Max Frame Length(byte) 1522 Generally, this parameter takes the default value of 1522 bytes. If jumbo frames with a greater length need to be transmitted, set the maximum frame length to the actual length of these jumbo frames.
Laser Interface Status On -

Table 3-17 describes the planning for E-Line service parameters.

Table 3-17 Parameters of E-Line services
Item Value in This Example Planning Guidelines
Service ID eth01 -
Service Type UNI-UNI -
MTU(bytes) 1500 -
L2VPN AC List-L2VPN AC-Port (GE port) GigabitEthernet0/16/0/1 -
VLAN/Aggregated VLAN - The occupied VLAN is null for point-to-point transparently transmitted E-Line services.
L2VPN AC List-L2VPN AC-Port (Vp port) Vp0/32/0/40001 -
VLAN/Aggregated VLAN - The occupied VLAN is null for point-to-point transparently transmitted E-Line services.

Configuring E-Line Services on a Per-NE Basis

This topic describes how to configure point-to-point transparently transmitted E-Line services on a per-NE basis, based on the service planning.

Prerequisites

  • You must be an NM user with "NE operator" authority or higher.
  • You must understand the networking, requirements and service planning of the example.

Tools, Equipment, and Materials

NMS

Procedure

  1. Configure Ethernet port attributes. Basic attributes and Layer 2 attributes need to be configured for point-to-point transparently transmitted E-Line services. Specifically, Encapsulation Type must be set to Null. For details about how to configure the attributes, see Configuring an Ethernet Port.

    Table 3-18 Parameters of Ethernet ports
    Item Value in This Example Planning Guidelines
    Encapsulation Type Null For a port that carries transparently transmitted point-to-point services, this parameter takes the fixed value of Null.
    Working Mode Auto-Negotiation
    • In this example, the GE port on the NodeB works in auto-negotiation mode. Therefore, the peer GE port must also work in auto-negotiation mode. If the peer Ethernet port works in another mode, the local Ethernet port must work in a consistent mode.
    • The working modes of the Ethernet ports within the backhaul network are uniformly planned as auto-negotiation.
    Max Frame Length(byte) 1522 Generally, this parameter takes the default value of 1522 bytes. If jumbo frames with a greater length need to be transmitted, set the maximum frame length to the actual length of these jumbo frames.
    Laser Interface Status On -

  2. Configure point-to-point transparently transmitted E-Line services. Specifically, Service Type must be set to UNI-UNI. For details about how to configure the services, see Configuring UNI-UNI E-Line Services.

    Table 3-19 Parameters of E-Line services
    Item Value in This Example Planning Guidelines
    Service ID eth01 -
    Service Type UNI-UNI -
    MTU(bytes) 1500 -
    L2VPN AC List-L2VPN AC-Port (GE port) GigabitEthernet0/16/0/1 -
    VLAN/Aggregated VLAN - The occupied VLAN is null for point-to-point transparently transmitted E-Line services.
    L2VPN AC List-L2VPN AC-Port (Vp port) Vp0/32/0/40001 -
    VLAN/Aggregated VLAN - The occupied VLAN is null for point-to-point transparently transmitted E-Line services.

Translation
Download
Updated: 2019-09-05

Document ID: EDOC1100033663

Views: 19415

Downloads: 682

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next