No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

OSN 9800 V100 Configuration Guide 03

This document introduces service configuration process for OSN 9800.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuration Example: Configuring VLAN-based E-Line Services

Configuration Example: Configuring VLAN-based E-Line Services

This topic uses a VLAN-based E-Line service as an example to describe how to configure Ethernet services based on the service plan.

Networking Diagram

This topic describes the NE networking.

Configure Ethernet services according to the following requirements:

  • NodeB1 and NodeB2 provide FE ports whose port rate is 100 Mbit/s.
  • Services transmitted by each NodeB carry VLAN IDs, and VLAN IDs on the entire network are uniformly planned.

To meet these requirements, you are advised to configure VLAN-based E-Line services.

Figure 3-28 Networking diagram (VLAN-based E-Line services)

Service Planning

This topic describes the service planning information about the VLAN-based E-Line services.

Table 3-20 describes the planning for Ethernet port parameters.

Table 3-20 Parameters of Ethernet ports
Item Value in This Example Planning Guidelines
Encapsulation Type 802.1Q For a port that carries VLAN-based E-Line services, this parameter takes the fixed value of 802.1Q.
Working Mode Auto-Negotiation
  • In this example, the FE/GE port on the NodeB works in auto-negotiation mode. Therefore, the peer FE/GE port must also work in auto-negotiation mode. If the peer Ethernet port works in another mode, the local Ethernet port must work in a consistent mode.
  • The working modes of the Ethernet ports within the backhaul network are uniformly planned as auto-negotiation.
Max Frame Length(byte) 1522 Generally, this parameter takes the default value of 1522 bytes. If jumbo frames with a greater length need to be transmitted, set the maximum frame length to the actual length of these jumbo frames.
Laser Interface Status On -
Tag Tag Aware In this example, all the services carry VLAN IDs. Therefore, the tag attribute of all the service ports is Tag Aware.

Table 3-21 describes the planning for Ethernet virtual interface parameters.

Table 3-21 Parameters of Ethernet virtual interfaces
Item Value in This Example Planning Guidelines
NE1 NE3 NE4
Interface Number 1 2 1 2 -
Interface Class Sub-interface Sub-interface Sub-interface Sub-interface -
Sub-Interface Type Stacking sub-interface Stacking sub-interface Stacking sub-interface Stacking sub-interface -
Port Type GE GE GE GE -
Associated Port (GE port) GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 -
Aggregated VLAN 120 110 120 110 Configure the source VLAN based on the service planning.

Table 3-22 describes the planning for E-Line service parameters.

Table 3-22 Parameters of E-Line services
Item Value in This Example Planning Guidelines
NE1 NE3 NE4
Service ID 1 2 1 2 -
Service Type UNI-UNI UNI-UNI UNI-UNI UNI-UNI -
MTU(bytes) 1500 1500 1500 1500 -
L2VPN AC List-L2VPN AC-Port (GE port) GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 -
VLAN/Aggregated VLAN 120 110 120 110 Configure the source VLAN based on the service planning.
L2VPN AC List-L2VPN AC-Port (Vp port) Vp0/32/0/40001 Vp0/32/0/40002 Vp0/32/0/40001 Vp0/32/0/40002 -

Configuring E-Line Services on a Per-NE Basis

This topic describes how to configure VLAN-based E-Line services on a per-NE basis, based on the service planning.

Prerequisites

  • You must be an NM user with "NE operator" authority or higher.
  • You must understand the networking, requirements and service planning of the example.

Tools, Equipment, and Materials

NMS

Procedure

  1. Configure Ethernet port attributes. Basic attributes and Layer 2 attributes need to be configured for VLAN-based E-Line services. Specifically, Encapsulation Type must be set to 802.1Q. For details about how to configure the attributes, see Configuring an Ethernet Port.

    Table 3-23 Parameters of Ethernet ports
    Item Value in This Example Planning Guidelines
    Encapsulation Type 802.1Q For a port that carries VLAN-based E-Line services, this parameter takes the fixed value of 802.1Q.
    Working Mode Auto-Negotiation
    • In this example, the FE/GE port on the NodeB works in auto-negotiation mode. Therefore, the peer FE/GE port must also work in auto-negotiation mode. If the peer Ethernet port works in another mode, the local Ethernet port must work in a consistent mode.
    • The working modes of the Ethernet ports within the backhaul network are uniformly planned as auto-negotiation.
    Max Frame Length(byte) 1522 Generally, this parameter takes the default value of 1522 bytes. If jumbo frames with a greater length need to be transmitted, set the maximum frame length to the actual length of these jumbo frames.
    Laser Interface Status On -
    Tag Tag Aware In this example, all the services carry VLAN IDs. Therefore, the tag attribute of all the service ports is Tag Aware.

  2. Create and configure Ethernet virtual interfaces based on the service planning. For details, see Configuring Ethernet Virtual Interfaces.

    Table 3-24 Parameters of Ethernet virtual interfaces
    Item Value in This Example Planning Guidelines
    NE1 NE3 NE4
    Interface Number 1 2 1 2 -
    Interface Class Sub-interface Sub-interface Sub-interface Sub-interface -
    Sub-Interface Type Stacking sub-interface Stacking sub-interface Stacking sub-interface Stacking sub-interface -
    Port Type GE GE GE GE -
    Associated Port (GE port) GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 -
    Aggregated VLAN 120 110 120 110 Configure the source VLAN based on the service planning.

  3. Configure VLAN-based E-Line services Specifically, Service Type must be set to UNI-UNI. For details about how to configure the services, see Configuring UNI-UNI E-Line Services.

    Table 3-25 Parameters of E-Line services
    Item Value in This Example Planning Guidelines
    NE1 NE3 NE4
    Service ID 1 2 1 2 -
    Service Type UNI-UNI UNI-UNI UNI-UNI UNI-UNI -
    MTU(bytes) 1500 1500 1500 1500 -
    L2VPN AC List-L2VPN AC-Port (GE port) GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 GigabitEthernet0/16/0/1.1 GigabitEthernet0/16/0/1.2 -
    VLAN/Aggregated VLAN 120 110 120 110 Configure the source VLAN based on the service planning.
    L2VPN AC List-L2VPN AC-Port (Vp port) Vp0/32/0/40001 Vp0/32/0/40002 Vp0/32/0/40001 Vp0/32/0/40002 -

Translation
Download
Updated: 2019-09-05

Document ID: EDOC1100033663

Views: 18657

Downloads: 657

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next