No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - WLAN-AC

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document provides the concepts, configuration procedures, and configuration examples of WLAN-AC features.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring a WAPI-PSK Security Policy

Example for Configuring a WAPI-PSK Security Policy

Configuration Process

You need to configure and maintain WLAN features and functions in different profiles. These WLAN profiles include regulatory domain profile, radio profile, VAP profile, AP system profile, AP wired port profile, WIDS profile, and WDS profile. When configuring WLAN services, you need to set related parameters in the WLAN profiles and bind the profiles to the AP group or APs. After that, the configuration is delivered to and takes effect on the APs. WLAN profiles can reference one another; therefore, you need to know the relationships among the profiles before configuring them. For details about the profile relationships and their basic configuration procedure, see WLAN Service Configuration Procedure.

Networking Requirements

A residential community provides a WLAN with the SSID wlan-net so that residents can access the network anywhere at any time. As shown in Figure 7-21, the AP deployed in a resident's home is directly connected to the AC. STAs automatically obtain IP addresses.

Because the WLAN is open to users, there are potential security risks to service data. Users do not require high WLAN security, so no extra authentication system is required. STAs support WAPI, so a WAPI security policy using pre-shared key authentication can be configured. Unicast and broadcast keys are updated based on time to secure data transmission.

Figure 7-21  Networking diagram for configuring a WAPI-PSK security policy

Configuration Roadmap

  1. Configure WLAN basic services so that STAs can access the WLAN.
  2. Create a security profile and set the security policy to WAPI-PSK to meet security requirements of users.
Table 7-6  Data planning

Item

Data

DHCP server The AC functions as a DHCP server to assign IP addresses to the STAs and AP.
IP address pool for the AP 10.10.10.2-10.10.10.254/24
IP address pool for STAs 10.10.11.2-10.10.11.254/24
AC's source interface address VLANIF 100: 10.10.10.1/24
AP group
  • Name: ap-group1
  • Referenced profile: VAP profile wlan-vap and regulatory domain profile domain1
Regulatory domain profile
  • Name: domain1
  • Country code: CN
SSID profile
  • Name: wlan-ssid
  • SSID name: wlan-net
Security profile
  • Name: wlan-security
  • Security policy: WAPI-PSK
  • Encryption key: 1234567@
VAP profile
  • Name: wlan-vap
  • Service VLAN: VLAN 101
  • Referenced profile: SSID profile wlan-ssid and security profile wlan-security

Configuration Notes

No ACK mechanism is provided for multicast packet transmission on air interfaces. In addition, wireless links are unstable. To ensure stable transmission of multicast packets, they are usually sent at low rates. If a large number of such multicast packets are sent from the network side, the air interfaces may be congested. You are advised to configure multicast packet suppression to reduce impact of a large number of low-rate multicast packets on the wireless network. Exercise caution when configuring the rate limit; otherwise, the multicast services may be affected.
  • In direct forwarding mode, you are advised to configure multicast packet suppression on switch interfaces connected to APs.
  • In tunnel forwarding mode, you are advised to configure multicast packet suppression in traffic profiles of the AC.
  • The management VLAN and service VLAN cannot be configured the same.
  • When multiple VAP profiles are configured and share one service VLAN, enable inter-service VLAN proxy ARP if the data forwarding mode is set to tunnel.

Procedure

  1. Connect the AP and AC.

    # Add Eth2/0/0 to management VLAN 100 and service VLAN 101.

    NOTE:

    You are advised to configure port isolation on Eth2/0/0 that connects the AC to the AP. If port isolation is not configured, many broadcast packets will be transmitted in the VLANs or WLAN users on different APs can directly communicate at Layer 2.

    <Huawei> system-view
    [Huawei] sysname AC
    [AC] vlan batch 100 101
    [AC] interface ethernet 2/0/0
    [AC-Ethernet2/0/0] port link-type trunk
    [AC-Ethernet2/0/0] port trunk pvid vlan 100
    [AC-Ethernet2/0/0] port trunk allow-pass vlan 100 101
    [AC-Ethernet2/0/0] port-isolate enable
    [AC-Ethernet2/0/0] quit
    

  2. Configure the AC as a DHCP server to allocate IP addresses to the AP and STAs.

    # Configure the AC as the DHCP server to allocate an IP address to the AP from the interface IP address pool on VLANIF 100, and allocate IP addresses to STAs from the interface IP address pool on VLANIF 101.

    [AC] dhcp enable
    [AC] interface vlanif 100
    [AC-Vlanif100] ip address 10.10.10.1 24
    [AC-Vlanif100] dhcp select interface
    [AC-Vlanif100] quit
    [AC] interface vlanif 101
    [AC-Vlanif101] ip address 10.10.11.1 24
    [AC-Vlanif101] dhcp select interface
    [AC-Vlanif101] quit
    

  3. Configure the AP to go online.

    # Create an AP group and add the AP to the AP group.

    [AC] wlan ac
    [AC-wlan-view] ap-group name ap-group1
    Info: This operation may take a few seconds. Please wait for a moment.done.
    [AC-wlan-ap-group-ap-group1] quit
    

    # Create a regulatory domain profile, configure the AC country code in the profile, and apply the profile to the AP group.

    [AC-wlan-view] regulatory-domain-profile name domain1
    [AC-wlan-regulate-domain-domain1] country-code cn
    Info: The current country code is same with the input country code.
    [AC-wlan-regulate-domain-domain1] quit
    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] regulatory-domain-profile domain1
    Warning: Modifying the country code will clear channel, power and antenna gain configurations of the radio and reset the AP. Continu
    e?[Y/N]:y 
    [AC-wlan-ap-group-ap-group1] quit
    [AC-wlan-view] quit
    

    # Configure the AC's source interface.

    [AC] capwap source interface vlanif 100
    
    # Import the AP offline on the AC and add the AP to AP group ap-group1. Assume that the AP's MAC address is 60de-4476-e360. Configure a name for the AP based on the AP's deployment location, so that you can know where the AP is deployed from its name. For example, name the AP area_1 if it is deployed in Area 1.
    NOTE:

    The default AP authentication mode is MAC address authentication. If the default settings are retained, you do not need to run the ap auth-mode mac-auth command.

    [AC] wlan ac
    [AC-wlan-view] ap auth-mode mac-auth
    [AC-wlan-view] ap-id 0 ap-mac 60de-4476-e360
    [AC-wlan-ap-0] ap-name area_1
    [AC-wlan-ap-0] ap-group ap-group1
    Warning: This operation may cause AP reset. If the country code changes, it will clear channel, power and antenna gain configuration
    s of the radio, Whether to continue? [Y/N]:y 
    Info: This operation may take a few seconds. Please wait for a moment.. done.
    [AC-wlan-ap-0] quit
    

    # After the AP is powered on, run the display ap all command to check the AP state. If the State field is displayed as nor, the AP goes online normally.

    [AC-wlan-view] display ap all
    Info: This operation may take a few seconds. Please wait for a moment.done.
    Total AP information:
    nor  : normal          [1]
    ---------------------------------------------------------------------------------------------
    ID   MAC            Name   Group     IP           Type            State STA Uptime
    ---------------------------------------------------------------------------------------------
    0    60de-4476-e360 area_1 ap-group1 10.10.10.254 AP6010DN-AGN    nor   0   6S
    ---------------------------------------------------------------------------------------------
    Total: 1

  4. Configure WLAN service parameters.

    # Create the security profile wlan-security, set the security policy to WAPI-PSK, configure time-based unicast and multicast key updates, and set the update interval to 20,000s.

    [AC-wlan-view] security-profile name wlan-security
    [AC-wlan-sec-prof-wlan-security] security wapi psk pass-phrase 1234567@
    [AC-wlan-sec-prof-wlan-security] wapi usk key-update time-based
    [AC-wlan-sec-prof-wlan-security] wapi msk key-update time-based
    [AC-wlan-sec-prof-wlan-security] wapi usk-update-interval 20000
    [AC-wlan-sec-prof-wlan-security] wapi msk-update-interval 20000
    [AC-wlan-sec-prof-wlan-security] quit
    

    # Create the SSID profile wlan-ssid and set the SSID name to wlan-net.

    [AC-wlan-view] ssid-profile name wlan-ssid
    [AC-wlan-ssid-prof-wlan-ssid] ssid wlan-net
    Warning: This action may cause service interruption. Continue?[Y/N]y
    Info: This operation may take a few seconds, please wait.done.
    [AC-wlan-ssid-prof-wlan-ssid] quit
    

    # Create the VAP profile wlan-vap, set service VLAN, and apply the security profile and SSID profile to the VAP profile.

    [AC-wlan-view] vap-profile name wlan-vap
    [AC-wlan-vap-prof-wlan-vap] service-vlan vlan-id 101
    Info: This operation may take a few seconds, please wait.done.
    [AC-wlan-vap-prof-wlan-vap] security-profile wlan-security
    Info: This operation may take a few seconds, please wait..done.
    [AC-wlan-vap-prof-wlan-vap] ssid-profile wlan-ssid
    Info: This operation may take a few seconds, please wait..done.
    [AC-wlan-vap-prof-wlan-vap] quit
    

    # Bind the VAP profile wlan-vap to the AP group and apply the profile to radio of the AP.

    [AC-wlan-view] ap-group name ap-group1
    [AC-wlan-ap-group-ap-group1] vap-profile wlan-vap wlan 1 radio all
    Info: This operation may take a few seconds, please wait..done.
    [AC-wlan-ap-group-ap-group1] quit
    

    # Commit the configuration.

    [AC-wlan-view] commit all                                                
    Warning: Committing configuration may cause service interruption, continue?[Y/N]:y      

  5. Verify the configuration.

    The WLAN with SSID wlan-net is available for mobile phones connected to the AP.

    The mobile phone obtains an IP address after it associates with the WLAN. The mobile phone can access the WLAN after the wireless user enters the password.

Configuration Files

AC configuration file

#
 sysname AC
#
vlan batch 100 to 101 
#
dhcp enable
#
interface Vlanif100                                                             
 ip address 10.10.10.1 255.255.255.0                                            
 dhcp select interface
#
interface Vlanif101                                                             
 ip address 10.10.11.1 255.255.255.0                                            
 dhcp select interface
#
interface Ethernet2/0/0                                                         
 port link-type trunk                                                           
 port trunk pvid vlan 100                                                       
 port trunk allow-pass vlan 100 to 101                                          
 port-isolate enable group 1
#
capwap source interface vlanif100
#
wlan ac
 security-profile name wlan-security
  security wapi psk pass-phrase %^%#kL2]1VAO|)F7HoN[KGx:~qPg~Ga|3Lk+T='O,`_X%^%#
  wapi usk-update-interval 20000
  wapi msk-update-interval 20000
 ssid-profile name wlan-ssid
  ssid wlan-net
 vap-profile name wlan-vap
  service-vlan vlan-id 101
  ssid-profile wlan-ssid
  security-profile wlan-security
 regulatory-domain-profile name domain1
ap-group name ap-group1
  regulatory-domain-profile domain1
  radio 0
   vap-profile wlan-vap wlan 1
  radio 1
   vap-profile wlan-vap wlan 1
  radio 2
   vap-profile wlan-vap wlan 1
 ap-id 0 type-id 19 ap-mac 60de-4476-e360 ap-sn 210235554710CB000042
  ap-name area_1
  ap-group ap-group1
#
return
Translation
Download
Updated: 2019-08-07

Document ID: EDOC1100033726

Views: 36134

Downloads: 220

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next