No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document provides the trap description, attributes, parameters, impact on the system, possible causes, procedures, and references. This document provides a complete set of traps, through which intended readers are kept of the running status of the device so as to locate faults.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
SPR_1.3.6.1.4.1.2011.5.25.241.2.2.1.1 hwSPRLinkReport

SPR_1.3.6.1.4.1.2011.5.25.241.2.2.1.1 hwSPRLinkReport

Description

SPR/4/SPRLINKCHANGE:OID [oid] SPR Link-state changed .LinkStateIndex = [integer], LinkStateName = [octet], LinkStateEligibility = [integer].

This alarm is generated when link quality parameters on a detection link become correct or incorrect.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.241.2.2.1.1 Warning qualityOfServiceAlarm(3)

Parameters

Name Meaning
OID

Indicates the MIB object ID of the alarm.

LinkStateIndex Indicates the index. The value ranges from 1 to 65535.
LinkStateName Indicates the interface name.
LinkStateEligibility Indicates the link status:
  • 0: indicates that the link is Up.
  • 1: indicates that the link is Down.

Impact on the System

  • If a detection link reports this alarm when SPR is configured, the link may be unavailable.
  • If a link sometimes reports this alarm, services may be switched normally.
  • If a link frequently reports this alarm, link flapping occurs.

Possible Causes

  1. Traffic is switched between links.
  2. The link configuration is incorrect.
  3. The threshold configuration is incorrect.
  4. The link fails.

Procedure

  1. Run the display smart-policy-route link-state command to view the detection link status.

    • Check whether the loss ratio is 1000. If yes, the link is faulty. Go to step 4.
    • Check whether the delay, jitter, loss ratio, and CMI are correct. If yes, go to step 2.
    • If the link status is not found, go to step 3.

  2. Run the display smart-service-profile service-map name command to view thresholds for link quality parameters.

    • Check whether the link meets service requirements based on the link status. If link does not meet service requirements, services may be switched between links. Go to step 5.
    • Check whether the thresholds for link quality parameters are correct. If the thresholds for link quality parameters are incorrect, set correct thresholds for link quality parameters.
      • Run the set delay threshold threshold-value command to set the threshold for the delay.
      • Run the set jitter threshold threshold-value command to set the threshold for the jitter.
      • Run the set loss threshold threshold-value command to set the threshold for the loss ratio.
      • Run the set cmi threshold threshold-value command to set the threshold for the CMI.
      • Run the cmi-method cmi-method command to set the CMI formula.
      Go to step 5.

  3. Run the display nqa results [ test-instance admin-name test-name ] command to check whether the NQA test instance type is jitter.

    • If the NQA test instance type is jitter, the link is faulty. Go to step 4.
    • If the NQA test instance type is not jitter, reconfigure an NQA test instance and detection link. Go to step 5.

  4. Collect the alarm information, log information, and configuration information, and then contact technical support personnel.
  5. End.

Related Information

None.

Translation
Download
Updated: 2019-08-12

Document ID: EDOC1100034065

Views: 143588

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next