No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document provides the trap description, attributes, parameters, impact on the system, possible causes, procedures, and references. This document provides a complete set of traps, through which intended readers are kept of the running status of the device so as to locate faults.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
L2V_1.3.6.1.4.1.2011.5.25.119.4.1.4.4 hwSvcUp

L2V_1.3.6.1.4.1.2011.5.25.119.4.1.4.4 hwSvcUp

Description

L2V/2/SVC_UP_T:OID [oid] The status of the SVC VC turned UP. (InterfaceIndex=[INTEGER], InterfaceIndex=[INTEGER], SvcId=[GAUGE], SVcType=[INTEGER], PeerAddress=[IPADDR], SvcInboundLabel=[GAUGE], SvcOutboundLabel=[GAUGE], HWL2VpnStateChangeReason=[INTEGER], InterfaceName=[STRING], TunnelPolicyName=[STRING], ActiveState=[INTEGER])

The trap was generated when the SVC VC was Up.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.4.1.2011.5.25.119.4.1.4.4

Major

other(1)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

InterfaceIndex

Index of the interface used as the table index.

InterfaceIndex

Index of the interface reported to the network management system as a parameter .

SvcId

Indicates the ID of an SVC.

SVcType

Indicates the type of an SVC:
  • 0: Initial value
  • 1: FR
  • 2: ATM AAL5
  • 3: ATM cell relay
  • 4: VLAN
  • 5: Ethernet
  • 6: HDLC
  • 7: PPP
  • 9: ATM cell VCC
  • 10: ATM cell VPC
  • 11: IP-layer 2 (used for heterogeneous IP-interworking between Huawei devices and non-Huawei devices)
  • 12: ATM, 1-to-1 VCC cell mode
  • 13: ATM, 1-to-1 VPC cell mode
  • 14: ATM, AAL5 PDU VCC TRANSPORT
  • 64: Heterogeneous IP-interworking

PeerAddress

Indicates the IP address of a peer.

SvcInboundLabel

Indicates the incoming label of an SVC.

SvcOutboundLabel

Indicates the outgoing label of an SVC.

HWL2VpnStateChangeReason

Indicates the cause for the SVC status change.

InterfaceName

Indicates the interface name.

TunnelPolicyName

Indicates the name of a tunnel policy.

ActiveState

Indicates the status of active.

Impact on the System

The SVC service is recovered.

Possible Causes

An SVC goes Up.

Procedure

  1. This trap message is informational only, and no action is required.
Translation
Download
Updated: 2019-08-12

Document ID: EDOC1100034065

Views: 149798

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next