No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Alarm Handling

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document provides the trap description, attributes, parameters, impact on the system, possible causes, procedures, and references. This document provides a complete set of traps, through which intended readers are kept of the running status of the device so as to locate faults.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
LDP_1.3.6.1.2.1.10.166.4.0.1 mplsLdpInitSessionThresholdExceeded

LDP_1.3.6.1.2.1.10.166.4.0.1 mplsLdpInitSessionThresholdExceeded

Description

LDP/4/SSNTHRESHOLDEXCEED: [oid] The number of failures in LDP session negotiation reached threshold. (LdpId=[OPAQUE], LdpEntityIndex=[GAUGE], Times=[INTEGER])

The value of mplsLdpEntityInitSesThreshold is not 0, and the number of times for session negotiation through Init messages exceeds this threshold.

Attribute

Alarm ID Alarm Severity Alarm Type
1.3.6.1.2.1.10.166.4.0.1

Warning

environmentalAlarm(6)

Parameters

Name Meaning

oid

Indicates the MIB object ID of the alarm.

LdpId

Indicates the local LDP peer ID.

LdpEntityIndex

Indicates the index of an LDP entity.

Times

Indicates the number of session initialization messages sent.

Impact on the System

The session cannot be set up. The original services or newly added ones that depend on the session are interrupted.

Possible Causes

1. Label advertisement mode changes, and the label advertisement modes are inconsistent on the two ends of the session. The version does not support the DOD mode. The trap is generated when the peer supports the DOD mode during interworking.

2. The negotiation of the Keepalive period fails. The trap is generated when the Keepalive period of the peer is 0. In this version, the minimum value of the Keepalive period is set to 30. The trap is generated when the Keepalive period of the peer can be set to 0.

Procedure

  1. Check whether the devices at the two ends of the session are Huawei devices.

    • If so, go to Step 2.

    • If not, go to Step 3.

  2. In this case, the trap message is not generated. Go to Step 6.
  3. Check the configurations of the Huawei devices, and run the display current-configuration configuration mpls-ldp command to check whether other configurations exist in the MPLS LDP view.

    • If so, go to Step 4.

    • If not, go to Step 5.

  4. The setup of the session is not affected even if other configurations exist in the MPLS LDP view. Save the configurations, and then go to Step 6.
  5. It can be concluded that the fault is caused by the configuration of the peer. In this case, go to Step 7.
  6. Collect alarm information and configuration information, and then contact technical support personnel.
  7. Contact the technical personnel of the peer vendor, and then go to Step 8.
  8. End.

Related Information

None

Translation
Download
Updated: 2019-08-12

Document ID: EDOC1100034065

Views: 137536

Downloads: 42

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next