No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - Basic Configuration

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document provides the basic concepts, configuration procedures, and configuration examples in different application scenarios of the Basic configuration supported by the device.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for Auto-Config

Licensing Requirements and Limitations for Auto-Config

This section provides prerequisites for configuring Auto-Config, interfaces that support Auto-Config, and configuration notes.

Involved Network Elements

None

Licensing Requirements

Auto-Config is a basic feature of a router and is not under license control.

Feature Limitations

  • AR100 series, AR120 series (except AR129 and AR129GW-L), AR150 series (except AR156, AR156W, AR157, AR157G-HSPA+7, AR157VW, AR157W, AR158E, and AR158EVW), AR160 series (except AR161FW-P-M5), AR201, AR1200 series, AR2200 series, and AR3200 series support Auto-Config function.

  • The management interfaces of the AR1200, AR2200, AR3200, and AR3600 series do not support the Auto-Config function.

  • In deployment, you can use Auto-Config to configure the device or manually configure the device. If the device is manually configured, Auto-Config is disabled automatically.
  • The device can be configured using Auto-Config or USB deployment. However, two deployment methods cannot be used together. If you need to use the Auto-Config function after USB-based deployment has been performed on the device, you need to run the set factory-configuration from default command to specify the default factory settings as factory settings.
  • When the factory settings are being restored, only unconfigured WAN interfaces support the Auto-Config function.
  • Devices to be configured must be new devices, that is, no startup configuration file with file name extension .cfg or .zip exists on the device.
  • You can obtain the MAC address and ESN of the device in the following ways:
    • Check the label on the device.

    • Log in to the device and run the display system-mac command in the diagnosis view and the display esn command.

  • The following interfaces support the Auto-Config function:
    • AR100 series: GE0/0/4
    • AR121, AR121W, AR121GW-L: Eth0/0/4

    • AR129CGVW-L: GE0/0/4
    • AR150 series (except AR156, AR157, AR157W, AR157VW, AR157G-HSPA+7, AR158EVW and AR156W): Eth0/0/4

    • AR160 series (except AR169 and AR169G-L): GE0/0/4
    • AR160 series (AR169 and AR169G-L): GE0/0/3
    • AR200 series (except AR206, AR207, AR207V, AR207V-P, AR208E, AR207G-HSPA+7 and AR207VW): Eth0/0/8

    • AR1200 series, AR2200 series, and AR3200 series: Layer 3 Ethernet interfaces except for the management interface, GPON interface, and EPON interface

      When a GPON or EPON interface is used to implement the Auto-Config function on a device, the system automatically creates a sub-interface numbered 4094. In addition, the system sets the encapsulation mode of the sub-interface to dot1q and the VLAN tag allowed by the sub-interface to 4000. Therefore, the device and DHCP server must exchange packets of VLAN 4000.

  • When users log in to the new device or devices with no startup configuration files through the console interface, the system prompts the following information: "Auto-Config is working. Before configuring the device, stop Auto-Config. If you perform configurations when Auto-Config is running, the DHCP, routing, DNS, and VTY configurations will be lost. Do you want to stop Auto-Config? [y/n]:".
    • To continue Auto-Config, enter n.
    • To stop Auto-Config, enter y.
      If you do not want to run Auto-Config but enter n, the DHCP, routing, DNS, and VTY configurations will be lost after the choice.
Translation
Download
Updated: 2019-11-21

Document ID: EDOC1100034066

Views: 85537

Downloads: 476

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next