No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Unicast Routing

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document describes the concepts and configuration procedures of IP Service features on the device, and provides the configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring IS-IS Route Summarization

Example for Configuring IS-IS Route Summarization

Networking Requirements

As shown in Figure 7-35, three routers run IS-IS to communicate with each other. RouterA is a Level-2 router, RouterB is a Level-1-2 router, and RouterC is a Level-1 router. RouterA is heavily loaded because there are too many routing entries on the IS-IS network. Therefore, system resource consumption of RouterA needs to be reduced.

Figure 7-35 Networking diagram of configuring IS-IS route summarization

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure IP addresses for interfaces and enable IS-IS on each router so that the routers can be interconnected.

  2. Configure route summarization on RouterB to reduce the routing table size of RouterA without affecting data forwarding so that the system resource consumption of RouterA can be reduced.

Procedure

  1. Configure IP addresses for interfaces on each router.

    # Configure RouterA.

    <Huawei> system-view
    [Huawei] sysname RouterA
    [RouterA] interface gigabitethernet 2/0/0
    [RouterA-GigabitEthernet2/0/0] ip address 172.2.1.1 24
    [RouterA-GigabitEthernet2/0/0] quit

    The configurations of RouterB and RouterC are similar to the configuration of RouterA, and are not mentioned here.

  2. Configure basic IS-IS functions.

    # Configure RouterA.

    [RouterA] isis 1
    [RouterA-isis-1] is-level level-2
    [RouterA-isis-1] network-entity 20.0000.0000.0001.00
    [RouterA-isis-1] quit
    [RouterA] interface gigabitethernet 2/0/0
    [RouterA-GigabitEthernet2/0/0] isis enable 1
    [RouterA-GigabitEthernet2/0/0] quit

    # Configure RouterB.

    [RouterB] isis 1
    [RouterB-isis-1] network-entity 10.0000.0000.0002.00
    [RouterB-isis-1] quit
    [RouterB] interface gigabitethernet 2/0/0
    [RouterB-GigabitEthernet2/0/0] isis enable 1
    [RouterB-GigabitEthernet2/0/0] quit
    [RouterB] interface gigabitethernet 1/0/0
    [RouterB-GigabitEthernet1/0/0] isis enable 1
    [RouterB-GigabitEthernet1/0/0] quit

    # Configure RouterC.

    [RouterC] isis 1
    [RouterC-isis-1] is-level level-1
    [RouterC-isis-1] network-entity 10.0000.0000.0003.00
    [RouterC-isis-1] quit
    [RouterC] interface gigabitethernet 1/0/0
    [RouterC-GigabitEthernet1/0/0] isis enable 1
    [RouterC-GigabitEthernet1/0/0] quit

    The configurations of GigabitEthernet2/0/0, GigabitEthernet3/0/0, and GigabitEthernet4/0/0 are similar to the configuration of GigabitEthernet1/0/0, and are not mentioned here.

  3. Check the IS-IS routing table of RouterA.

    [RouterA] display isis route
                             Route information for ISIS(1)
                             -----------------------------
                            ISIS(1) Level-2 Forwarding Table
                            --------------------------------
     IPV4 Destination     IntCost    ExtCost ExitInterface  NextHop          Flags
    ----------------------------------------------------------------------------
     172.1.1.0/24         30         NULL    GE2/0/0        172.2.1.2      A/-/L/-
     172.1.2.0/24         30         NULL    GE2/0/0        172.2.1.2      A/-/L/-
     172.1.3.0/24         30         NULL    GE2/0/0        172.2.1.2      A/-/L/-
     172.1.4.0/24         20         NULL    GE2/0/0        172.2.1.2      A/-/L/-
     172.2.1.0/24         10         NULL    GE2/0/0        Direct         D/-/L/-
         Flags: D-Direct, A-Added to URT, L-Advertised in LSPs, S-IGP Shortcut,
                                   U-Up/Down Bit Set

  4. Configure route summarization on RouterB.

    # Summarize 172.1.1.0/24, 172.1.2.0/24, 172.1.3.0/24, and 172.1.4.0/24 into 172.1.0.0/16 on RouterB.

    [RouterB] isis 1
    [RouterB-isis-1] summary 172.1.0.0 255.255.0.0 level-1-2
    [RouterB-isis-1] quit

  5. Verify the configuration.

    # Check the routing table of RouterA, you can see that routes 172.1.1.0/24, 172.1.2.0/24, 172.1.3.0/24 and 172.1.4.0/24 are summarized into one route 172.1.0.0/16.

    [RouterA] display isis route
                             Route information for ISIS(1)
                             -----------------------------
                            ISIS(1) Level-2 Forwarding Table
                            --------------------------------
     IPV4 Destination     IntCost    ExtCost ExitInterface   NextHop         Flags
    ----------------------------------------------------------------------------
     172.1.0.0/16         20         NULL    GE2/0/0        172.2.1.2      A/-/L/-
     172.2.1.0/24         10         NULL    GE2/0/0        Direct         D/-/L/-
         Flags: D-Direct, A-Added to URT, L-Advertised in LSPs, S-IGP Shortcut,
                                   U-Up/Down Bit Set

Configuration Files

  • Configuration file of RouterA

    #
     sysname RouterA
    #
    isis 1
     is-level level-2
     network-entity 20.0000.0000.0001.00
    #
    interface GigabitEthernet2/0/0
     ip address 172.2.1.1 255.255.255.0
     isis enable 1
    #
    return
  • Configuration file of RouterB

    #
     sysname RouterB
    #
    isis 1
     network-entity 10.0000.0000.0002.00
     summary 172.1.0.0 255.255.0.0 level-1-2
    #
    interface GigabitEthernet1/0/0
     ip address 172.1.4.2 255.255.255.0
     isis enable 1
    #
    interface GigabitEthernet2/0/0
     ip address 172.2.1.2 255.255.255.0
     isis enable 1
    #
    return
  • Configuration file of RouterC

    #
     sysname RouterC
    #
    isis 1
     is-level level-1
     network-entity 10.0000.0000.0003.00
    #
    interface GigabitEthernet1/0/0
     ip address 172.1.4.1 255.255.255.0
     isis enable 1
    #
    interface GigabitEthernet2/0/0
     ip address 172.1.1.1 255.255.255.0
     isis enable 1
    #
    interface GigabitEthernet3/0/0
     ip address 172.1.2.1 255.255.255.0
     isis enable 1
    #
    interface GigabitEthernet4/0/0
     ip address 172.1.3.1 255.255.255.0
     isis enable 1
    #
    return
Translation
Download
Updated: 2019-08-12

Document ID: EDOC1100034072

Views: 114071

Downloads: 168

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next