No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - IP Unicast Routing

AR100, AR120, AR150, AR160, AR200, AR1200, AR2200, AR3200, and AR3600 V200R010

This document describes the concepts and configuration procedures of IP Service features on the device, and provides the configuration examples.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Static BFD for RIP

Configuring Static BFD for RIP

Context

BFD provides link failure detection featuring light load and high speed. Static BFD for RIP is a mode to implement the BFD function.

Establishing BFD sessions between RIP neighbors can rapidly detect faults on links and speed up response of RIP to network topology changes. Static BFD implements the following functions:
  • One-arm BFD: If some devices on a network support BFD but some do not, configure one-arm BFD to implement fault detection.
  • Two-arm BFD: If all the devices on a network support BFD, configure two-arm BFD to implement fault detection.

Static BFD must be enabled using a command.

Procedure

  1. Enable BFD globally.
    1. Run system-view

      The system view is displayed.

    2. Run bfd

      BFD is enabled globally.

    3. Run quit

      Return to the system view.

    NOTE:

    To configure one-arm BFD, go to Step 2. To configure two-arm BFD, go to Step 3.

  2. Configure one-arm BFD.
    1. Run bfd session-name bind peer-ip peer-ip interface interface-type interface-number [ source-ip source-ip ] one-arm-echo

      BFD is enabled between the specified interface and peer device.

      If a peer IP address and a local interface are specified, BFD detects only a single-hop link, that is, a route with the interface specified in the bfd command as the outbound interface and with the peer IP address specified in the peer-ip command as the next-hop address.

      NOTE:

      When configuring the one-arm Echo function on the device, set the source-ip source-ip to the IP address of an interface on the device. Ensure that the peer device can ping this IP address.

    2. Run discriminator local discr-value

      The local discriminator is set.

    3. (Optional) Run min-echo-rx-interval interval

      The minimum interval at which BFD packets are received is configured.

    4. Run commit

      The configuration is committed.

    5. Run quit

      Return to the system view.

  3. Configure two-arm BFD.
    1. Run bfd session-name bind peer-ip ip-address [ interface interface-type interface-number ] [ source-ip ip-address ]

      BFD binding is created.

      If a peer IP address and a local interface are specified, BFD detects only a single-hop link, that is, a route with the interface specified in the bfd command as the outbound interface and with the peer IP address specified in the peer-ip command as the next-hop address.

    2. Set discriminators.

      • Run discriminator local discr-value

        The local discriminator is set.

      • Run discriminator remote discr-value

        The remote discriminator is set.

      The local discriminator must be the remote discriminator of the device on the other end; otherwise, a BFD session cannot be established. The local and remote discriminators cannot be modified after being configured.

      NOTE:

      local discr-value set on the local device is the same as that of remote discr-value set on the remote device.remote discr-value set on the local device is the same as that of local discr-value set on the remote device.

    3. Run commit

      The configuration is committed.

    4. Run quit

      Return to the system view.

  4. Enable static BFD on an interface.
    1. Run interface interface-type interface-number

      The view of the specified interface is displayed.

    2. Run rip bfd static

      Static BFD is enabled on the interface.

    3. Run quit

      Return to the system view.

Verifying the Configuration

After configuring static BFD for RIP,
  • Run the display rip process-id interface [ interface-type interface-number ] verbose command to check BFD for RIP configurations on the specified interface.
Translation
Download
Updated: 2019-05-20

Document ID: EDOC1100034072

Views: 111271

Downloads: 163

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next