No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

CLI-based Configuration Guide - AMI

AR500, AR510, AR531, AR550, AR1500, and AR2500 V200R010

This document describes the principles and configurations of the AMI features, and provides configuration examples of these features.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring AMI Through Uplink LTE/WCDMA

Example for Configuring AMI Through Uplink LTE/WCDMA

Networking Requirements

Figure 2-6 shows a remote area where meters are sparsely distributed. The DCU (RouterA) functions as the data concentrator to manage all the meters in this area in a centralized manner. RouterA connects to a DCPr Through Uplink LTE/WCDMA and connects to meters through PLC channels.

Meters in this residential area need to be managed in a unified manner and automated meter data reading must be implemented.

Figure 2-6  Networking diagram of configuring AMI through uplink LTE/WCDMA

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure an LTE cellular interface to implement communication between the device (RouterA) and DCP through the WCDMA network.
  2. Configure basic device information and connection between the device and DCP to enable the device to register with the DCP. Configure the authentication level and ensure that the device and DCP have the same authentication level so that the two devices can authenticate each other.
  3. Configure communication between the device and meters through PLC channels for meter management.

Procedure

  1. Configure RouterA to communicate with the DCP through LTE/WCDMA.

    # Create an APN profile.

    <Huawei> system-view
    [Huawei] sysname Router
    [Router] apn profile lteprofile
    [Router-apn-profile-lteprofile] apn ltenet
    [Router-apn-profile-lteprofile] sim-id 1
    [Router-apn-profile-lteprofile] quit

    # Obtain IP addresses dynamically.

    [Router] interface cellular 0/0/0
    [Router-Cellular0/0/0] ip address negotiate

    # Configure a network connection mode.

    [Router-Cellular0/0/0] mode lte wcdma-only
    [Router-Cellular0/0/0] quit

    # Configure a dialer control list.

    [Router] dialer-rule
    [Router-dialer-rule] dialer-rule 1 ip permit
    [Router-dialer-rule] quit

    # Enable circular DCC.

    [Router] interface cellular 0/0/0
    [Router-Cellular0/0/0] dialer enable-circular
    [Router-Cellular0/0/0] dialer-group 1
    NOTE:

    The value of the group-number parameter in the dialer-group command must be the same as that of dialer-rule-number in the dialer-rule command.

    # Configure the dialer number.

    [Router-Cellular0/0/0] dialer number *99# autodial
    [Router-Cellular0/0/0] dialer timer autodial 10
    

    # Bind the APN profile to the LTE cellular interface.

    [Router-Cellular0/0/0] apn-profile lteprofile
    [Router-Cellular0/0/0] shutdown
    [Router-Cellular0/0/0] undo shutdown
    [Router-Cellular0/0/0] quit

    # Configure a default route and specify Cellular0/0/0 as the outbound interface.

    [RouterA] ip route-static 0.0.0.0 0 cellular 0/0/0
  2. Configure the connection between RouterA and the DCP.

    # Set the heartbeat interval and maximum number of report retries.

    [RouterA] ami
    [RouterA-ami] basic heart-interval 2
    [RouterA-ami] basic report-retry 5

    # Configure a terminal ID and high-level authentication password Huawei123.

    [RouterA-ami] basic id HWT0AC853DDF0D13 password high
     Enter Password( Length: password<6-16> ):
     Confirm password: 
    [RouterA-ami] basic high-algorithm sha-256

    # Configure low-level authentication password Huawei123.

    [RouterA-ami] basic id HWT0AC853DDF0D13 password low
     Enter Password( Length: password<6-16> ):
     Confirm password: 
    

    # Configure the connection name.

    [RouterA-ami] connection dcp1

    # Set the local connection type of RouterA to TCP client.

    [RouterA-ami-connection-dcp1] parameter protocol-type iec62056
    [RouterA-ami-connection-dcp1] parameter connection-type tcp-client remote 192.168.1.19 port 4040 time-out 10 retry-wait 15
    [RouterA-ami-connection-dcp1] quit
  3. Configure RouterA to communicate with meters.

    # Configure the whitelist.

    [RouterA] whitelist channel-type hi-plc enable
    [RouterA] whitelist channel-type hi-plc append mac-address 541600102590
    
  4. Verify the configuration.

    # Run the display interface Cellular 0/0/0 command to check the interface configuration. The command output indicates that when traffic is forwarded through the interface, both the physical layer status and link layer status of the interface are Up, and the IP address obtained dynamically is 10.10.10.160/32.

    <RouterA> display interface Cellular 0/0/0
    Cellular0/0/0 current state : UP                                                
    Line protocol current state : UP                                                
    Last line protocol up time : 2000-04-08 00:25:01                                
    Description:HUAWEI, AR Series, Cellular0/0/0 Interface                          
    Route Port,The Maximum Transmit Unit is 1500, Hold timer is 10(sec)             
    Internet Address is negotiated, 10.10.10.160/32                                 
    Last physical up time   : 2000-04-08 00:25:01                                   
    Last physical down time : 2000-04-08 00:23:58                                   
    Current system time: 2000-04-08 00:31:16                                        
    Modem State: Present                                                            
    Model = B310s-927                                                               
    Current Network Connection = WCDMA(WCDMA)                                       
    Current RSSI = -93 dBm (weak)                                                   
    Last 300 seconds input rate 0 bytes/sec 0 bits/sec 0 packets/sec                
    Last 300 seconds output rate 0 bytes/sec 0 bits/sec 0 packets/sec               
    Input: 0 packets, 0 bytes                                                       
      Unicast:                  0,    Ununicast:                  0                 
                                                                                    
    Output: 0 packets, 0 bytes                                                      
      Unicast:                  0,    Ununicast:                  0                 
        Input bandwidth utilization  :    0%                                        
        Output bandwidth utilization :    0% 

    # Check information about all call sessions on the LTE modem. The following command output indicates that the APN is ltenet, the network type is WCDMA, and the network connection mode is WCDMA only.

    <RouterA> display Cellular 0/0/0 all
    Modem State:                                                                    
    Hardware Information.                                                           
    =====================                                                           
    Model = B310s-927                                                               
    Modem Type = LTE module                                                         
    Modem Firmware Version =  24.811.03.00.00                                       
    Hardware Version = WL1B310TM                                                    
    Integrate circuit card identity (ICCID) = 98681020100202000060                  
    International Mobile Subscriber Identity (IMSI) = 460070075590090               
    International Mobile Subscriber Identity (MSISDN) = None                        
    International Mobile Equipment Identity (IMEI) = 000000000000000                
    International Mobile Equipment Identity (MSISDN) = None                         
    Factory Serial Number (FSN) = 0123456789ABCDEF                                  
    Modem Status = Online                                                           
    Profile Information.                                                            
    ====================                                                            
    Profile 1 = ACTIVE                                                              
    --------                                                                        
    PDP Type = IPv4, Header Compression = OFF                                       
    Data Compression = OFF                                                          
    Access Point Name (APN) = ltenet                                                 
    Packet Session Status = Active                                                  
    * - Default profile                                                             
    Network Information.                                                            
    ====================                                                            
    Current Service Status = Service available                                      
    Service Domain = Combined                                                       
    Current Service = PS                                                            
    Packet Service = Attached                                                       
    Packet Session Status = Active                                                  
    Current Roaming Status = Roaming                                                
    Network Selection Mode = Automatic                                              
    Network Connection Mode = WCDMA only                                        
    Current Network Connection = WCDMA(WCDMA)                                       
    Mobile Country Code (MCC) = 460                                                 
    Mobile Network Code (MNC) = 07                                                  
    Mobile Operator Information = CHINA  MOBILE                                     
    Location Area Code (LAC) = 53000                                                
    Cell ID = 21037155                                                              
    Upstream Bandwidth = 384kbps                                                    
    Downstream Bandwidth = 384kbps                                                  
    Radio Information.                                                              
    ==================                                                              
    Current Band = AUTO                                                             
    Current RSSI = -95 dBm (weak)                                                   
    Current RSCP = -94 dBm                                                          
    Current ECIO = -13 dB                                                           
    Bands supported :                                                               
      GSM: GSM850 GSM900 GSM1800 GSM1900                                            
      WCDMA: WCDMA900 WCDMA2100                                                     
      FDD LTE: B3                                                                   
      TDD LTE: B40                                                                  
    Modem Security Information.                                                     
    ===========================                                                     
    SIM ID = 1                                                                      
    PIN Verification = Disabled                                                     
    PIN Status = Ready                                                              
    Number of Retries remaining = 3                                                 
    SIM Status = OK

    # Check configurations of the connection between RouterA and the DCP.

    <RouterA> display ami configuration connection dcp1
      Connection-dcp1 Connection config:                                            
      Peer device name: dcp-master                                                   
      Local connect type: tcp-client                                                
      Peer address: 192.168.1.19                                                     
      Peer port: 4040                                                               
      Proto type: iec62056 
    

    # Check the basic configurations of RouterA.

    <RouterA> display ami configuration basic
      Basic config:
      TerminalID: HWT0AC853DDF0D13
      HeartInterval: 2 min
      MaxRetryNum: 5
      HlsEncryptionAlgorithm: sha-256
      LowPassword: ******
      HighPassword: ******
    

    # Check the AMI status of RouterA.

    <RouterA> display ami status
      AMI Version : V200R005C60B170 
    
      Station name: dcp-master                                                      
      Peer address: 192.168.1.19                                                     
      Peer port: 4040                                                               
      Connection status: login
      Connect times: 3
      Receive message Byte: 1279
      Send message Byte: 1627                                                       
    

    # Display whitelist information of RouterA.

    [RouterA] display whitelist channel-type hi-plc
     ************************************************************
     Whitelist state : Enable
     Whitelist num: 1
     ------------------------------------------------------------
     Index        Mac Address
     ------------------------------------------------------------
     1            0x541600102590
     ************************************************************
    

Configuration Files

Configuration file of RouterA

# 
 sysname RouterA
#
 ami configuration file  flash:/ami_cfg.xml                  
 meter configuration file  flash:/meter_cfg.xml                
 dlms configuration file  flash:/proto_dlms_cfg.xml         
#
interface Cellular0/0/0 
 dialer enable-circular
 dialer-group 1
 apn-profile lteprofile
 dialer timer autodial 10 
 dialer number *99#
 ip address negotiate
#
dialer-rule
 dialer-rule 1 ip permit
#
apn profile lteprofile      
 apn ltenet      
#
ip route-static 0.0.0.0 0.0.0.0 Cellular0/0/0
#
return
Translation
Download
Updated: 2019-03-07

Document ID: EDOC1100034224

Views: 10024

Downloads: 20

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next