No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

X6800 Server V100R005 User Guide 01

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Logging In to the iBMC WebUI or CLI of the Server Node

Logging In to the iBMC WebUI or CLI of the Server Node

The server iBMC supports the CLI and WebUI management modes. You can log in to the iBMC WebUI or CLI to manage the server node.

Logging In to the iBMC CLI or WebUI of the Server Node Through the iBMC Management Network Port

Scenarios

Log in to the iBMC CLI or WebUI through the iBMC management network port on the server node.

NOTE:

If you log in to the iBMC CLI or WebUI through the iBMC management network port, the management network port mode must be the fixed or automatic mode.

Figure 4-14 shows the position of the iBMC management network port on the server node.

Figure 4-14 Position of the iBMC management network port
Data
  • IP address of the iBMC management network port on the server node
  • User name and password for logging in to the iBMC of the server node
Table 4-6 Default data

Category

Name

Default Value

iBMC management network port data

IP address and subnet mask of the management network port

  • The default IP addresses of the four server nodes in a 4U X6800 server are as follows:
    • Slot 1: 10.10.1.101
    • Slot 3: 10.10.1.103
    • Slot 5: 10.10.1.105
    • Slot 7: 10.10.1.107
    NOTE:

    N in "Node iBMC Default Network Setting 10.10.1.(100+N)" on the chassis label indicates the server node slot number, namely 1, 3, 5, and 7.

  • Default subnet mask: 255.255.255.0

iBMC login data

User name and password

  • Default user name: Administrator
  • Default password: Admin@9000
Software

PuTTY.exe (third-party software)

Procedure
  1. Connect the client to the iBMC management network port on the server node.

    Connect the client to the iBMC management network port on the server node using a network cable, as shown in Figure 4-15.
    Figure 4-15 Connecting the client to the management network port on the server node

  2. Set the client address.

    Set the IP address, subnet mask, or route of the client to enable the client to interconnect with the iBMC management network port on the server node.

    On the client, choose Start > Run, enter cmd, and click OK. Then, run the Ping IP address of the iBMC management network port command to check whether the iBMC management network port is reachable.

  3. (Optional) Log in to the iBMC WebUI of the server node.

    1. Open the browser on the client, enter the IP address of the iBMC management network port in the address box, and press Enter.
    2. Enter the user name and password on the WebUI shown in Figure 4-16, and click Log In.
      Figure 4-16 iBMC WebUI
      NOTE:

      You are advised to change the default password at the first login. For details, see Configuring the iBMC.

  4. (Optional) Log in to the iBMC CLI of the server node.

    1. On the client, double-click PuTTY.exe.

      The PuTTY Configuration window is displayed, as shown in Figure 4-17.

      Figure 4-17 PuTTY Configuration

    2. Set the login parameters.

      The parameters are described as follows:

      • Host Name (or IP address): Enter the IP address of the iBMC management network port on the server node, for example, 10.10.1.101.
      • Port: Retain the default value 22.
      • Connection type: Retain the default value SSH.
      • Close window on exit: Retain the default value Only on clean exit.
      NOTE:

      After you set Host Name (or IP address) and then Saved Sessions and click Save, you can simply double-click the saved settings under Saved Sessions to log in to the server.

    3. Click Open.

      The PuTTY window is displayed. Then the message "login as:" is displayed, prompting you to enter a user name.

      NOTE:
      • If you log in to the server for the first time, the PuTTY Security Alert dialog box is displayed. If you trust this site, click Yes. The PuTTY window is displayed.
      • If the entered user name or password is incorrect during server login, PuTTY must be connected again.
    4. Enter the user name and password as prompted.

      After login, the host name of the device is displayed on the left of the prompt.

Logging In to the iBMC CLI or WebUI of the Server Node Through the Aggregated Management Network Port

Scenarios

Network port aggregation indicates using the front or rear aggregated management network port as the management network port for the HMM and the iBMC, through which you can log in to the HMM and the iBMC of all server nodes. This function reduces the need for network cables and ports.

NOTE:

When both the iBMC management network port on the server node and the aggregated management network port are connected and the aggregated management network port is enabled on the server node, you can:

  • Log in to the iBMC CLI or WebUI of the server node through the aggregated management network port.
  • Log in to the HMM CLI through the aggregated management network port.

Log in to the iBMC CLI or WebUI of the server node through the front aggregated management network port on the mounting ear or the rear aggregated management network port on the HMM.

Figure 4-18 and Figure 4-19 shows the positions of the aggregated management network ports.

Figure 4-18 Position of the front aggregated management network port

Figure 4-19 Position of the rear aggregated management network port

Data
  • IP address of the iBMC management network port on the server node
  • User name and password for logging in to the iBMC of the server node
Software

PuTTY.exe (third-party software)

Procedure
  1. Connect the client to the aggregated management network port.

    Connect the client to the aggregated management network port using a network cable, as shown in Figure 4-20 or Figure 4-21.
    NOTE:

    Before configuring network port aggregation, ensure that the aggregated management port is connected with a network cable. Otherwise, the management connection will be interrupted after the configuration.

    Figure 4-20 Connecting the client to the front aggregated management network port

    Figure 4-21 Connecting the client to the rear aggregated management network port

  2. Connect the client to the iBMC management network port on the server node.

    Connect the client to the iBMC management network port on the server node using a network cable, as shown in Figure 4-22.
    Figure 4-22 Connecting the client to the iBMC management network port on the server node

  3. Set the client address.

    Set the IP address, subnet mask, or route of the client to enable the client to interconnect with the iBMC management network port on the server node.

    On the client, choose Start > Run, enter cmd, and click OK. Then, run the Ping IP address of the iBMC management network port command to check whether the iBMC management network port is reachable.

  4. Enable the network port aggregation function on the server node.

    • Method 1: Enable the iBMC aggregated network port on the server node using the iBMC WebUI.
      1. Log in to the iBMC WebUI of the server node.
      2. In the navigation tree, choose Configure > Network Settings.
      3. In the Select Mode area, set the network port mode to Fixed, and select the aggregated network port, as shown in Figure 4-23.
        Figure 4-23 Enabling the aggregated network port

      4. Click Save.
    • Method 2: Enable the iBMC aggregated network port on the server node using the iBMC CLI.
      1. Log in to the iBMC CLI of the server node.
      2. Run the following command to set the network mode to manual:
        iBMC:/->ipmcset -d netmode -v 1 
        Set net mode Manual successfully.
      3. Run the following command to enable network port aggregation:
        iBMC:/->ipmcset -d activeport -v 3 
        Set active port successfully.

  5. Remove the network cable from the iBMC management network port on the server node.
  6. (Optional) Log in to the iBMC WebUI of the server node.

    1. Open the browser on the client, enter the IP address of the iBMC management network port in the address box, and press Enter.
    2. Enter the user name and password on the WebUI shown in Figure 4-24, and click Log In.
      Figure 4-24 iBMC WebUI

      NOTE:

      You are advised to change the default password at the first login. For details, see Configuring the iBMC.

  7. (Optional) Log in to the iBMC CLI of the server node.

    1. On the client, double-click PuTTY.exe.

      The PuTTY Configuration window is displayed, as shown in Figure 4-25.

      Figure 4-25 PuTTY Configuration

    2. Set the login parameters.

      The parameters are described as follows:

      • Host Name (or IP address): Enter the IP address of the iBMC management network port on the server node, for example, 10.10.1.101.
      • Port: Retain the default value 22.
      • Connection type: Retain the default value SSH.
      • Close window on exit: Retain the default value Only on clean exit.
      NOTE:

      After you set Host Name (or IP address) and then Saved Sessions and click Save, you can simply double-click the saved settings under Saved Sessions to log in to the server.

    3. Click Open.

      The PuTTY window is displayed. Then the message "login as:" is displayed, prompting you to enter a user name.

      NOTE:
      • If you log in to the server for the first time, the PuTTY Security Alert dialog box is displayed. If you trust this site, click Yes. The PuTTY window is displayed.
      • If the entered user name or password is incorrect during server login, PuTTY must be connected again.
    4. Enter the user name and password as prompted.

      After login, the host name of the device is displayed on the left of the prompt.

Translation
Download
Updated: 2018-08-28

Document ID: EDOC1100036738

Views: 9439

Downloads: 33

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next