No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Displaying Optical Module Information

Displaying Optical Module Information

Context

If an optical module on an interface is faulty, you can run the display commands to view information about the optical module.

Procedure

  • Run the display transceiver [ interface interface-type interface-number | slot slot-id ] [ verbose ] command to view information about the optical module on a specified interface.

FAQ

What Is the Impact of Using Non-Huawei-Certified Optical Modules?

Huawei-certified optical modules have been tested to the highest standards to ensure their quality. Tests include the installation and removal, transmit and receive power, signal transmission quality, basic information query, fault tolerance, compatibility, electro magnetic compatibility (EMC), and environmental performance.

Therefore, non-Huawei-certified optical modules are not recommended. When a non-Huawei-certified optical module is used, the following problems often occur:
  • The optical module cannot be installed in an optical interface because of its nonstandard structure.

    The structure and size of some non-Huawei-certified optical modules do not comply with the MSA agreement. After such an optical module is installed in an optical interface, the neighbor interface cannot have an optical module installed because the non-Huawei-certified optical module has a nonstandard size.

  • The device data bus is abnormal because of the data bus defects of the non-Huawei-certified optical module.

    Some non-Huawei-certified optical modules have data bus design defects. When such an optical module is used on a device, the data bus of the device will become abnormal. As a result, data on the data bus cannot be read.

  • Improper edge connector size of the optical module damages the electronic components of optical interfaces.

    The edge connectors of some non-Huawei-certified optical modules have a nonstandard size, causing the interface to be short-circuited and damaging the electronic components of optical interfaces.

  • Optical module temperature monitoring is not standardized, causing alarms to be incorrectly generated.

    The temperature monitoring systems of some non-Huawei-certified optical modules do not comply with industry specifications, and so a high temperature is obtained. As a result, the system incorrectly reports a temperature alarm.

  • The optical module register is set incorrectly. Consequently, parameters and diagnostic information cannot be read or read incorrectly.

    The A0 registers of some non-Huawei-certified optical modules are set incorrectly. As a result, parameters and diagnostic information cannot be read or read incorrectly by the data bus.

  • The optical module design does not comply with the EMC, its anti-electromagnetic interference capability is low, and the optical module brings electromagnetic interference to surrounding devices.

  • The working temperature range of the optical module does not meet requirements, causing the optical power to be reduced at a high temperature. Subsequently, services are interrupted.

How Can I Determine Whether an Optical Module Is Huawei-Certified?

NOTICE:
  • A switch must use optical or copper modules that have been certified for use on Huawei switches. Non-certified optical or copper modules cannot ensure transmission reliability and may affect service stability. Huawei is not liable for any problem caused by the use of non-certified optical or copper modules and will not fix such problems.

  • The methods provided here are only for reference. To confirm whether optical modules you are using have been certified for use on Huawei switches, contact Huawei technical support.

10GE or Lower Speed Optical Modules

Huawei started certification on 10GE or lower speed optical modules for switch products on July 1, 2013.

To determine whether optical modules delivered for Huawei switches before July 1, 2013 are certified ones, contact Huawei technical support.

If your optical modules are delivered after July 1, 2013, use either of the following methods to determine whether they have been certified by Huawei.

Method 1: Check for "HUAWEI" on the label

If an optical module has been certified by Huawei, its label contains "HUAWEI", as shown in Figure 1-9.

Figure 1-9  "HUAWEI" on the label of a Huawei-certified switch optical module
Method 2: Run the display transceiver command

An optical module has received Huawei switch certification if it meets the following conditions:

  • In the display elabel command output, the Manufactured field displays a date later than 2013-07-01.

  • In the display version command output, the displayed version is V200R001C00 or later.

  • In the display transceiver command output, the Vendor Name field displays HUAWEI.

NOTE:

The SFP-FE-SX-MM1310 (part number: 02315233) is a Huawei-certified 100M optical module. However, the Vendor Name field displays the original manufacturer name, instead of HUAWEI.

For copper modules, the Vendor Name field also displays the original manufacturer name, instead of HUAWEI.

40GE and 100GE Optical Modules

Huawei started certification on 40GE and 100GE optical modules for switch products on January 1, 2016.

To determine whether optical modules delivered for Huawei switches before January 1, 2016 are certified ones, contact Huawei technical support.

If your optical modules are delivered after January 1, 2016, use either of the following methods to determine whether they have been certified by Huawei.

Method 1: Check for "HUAWEI" on the label

If an optical module has been certified by Huawei, its label contains "HUAWEI", as shown in Figure 1-9.

Method 2: Run the display transceiver command

A 40GE or 100GE optical module has received Huawei switch certification if it meets the following conditions:

  • In the display elabel command output, the Manufactured field displays a date later than 2016-01-01.

  • In the display version command output, the displayed version is V200R008 or later.

  • In the display transceiver command output, the Vendor Name field displays HUAWEI.

NOTE:

For the optical modules connected to high-speed cables or AOC cables, the Vendor Name field displays the original manufacturer name, instead of HUAWEI. For the methods of checking whether such an optical module has been certified by Huawei, contact technical support personnel.

What Can I Do If the Optical Power Is Low or High?

Fault Description

Optical power alarms occur when two optical interfaces are connected to each other.

Optical Power Alarms
BASETRAP_1.3.6.1.4.1.2011.5.25.129.2.17.1 hwOpticalPowerAbnormal     //An alarm indicating abnormal transmit or receive power of an optical module.
BASETRAP/3/OPTPWRABNORMAL: OID [oid] Optical module power is abnormal. (EntityPhysicalIndex=[INTEGER], BaseTrapSeverity=[INTEGER],
 BaseTrapProbableCause=[INTEGER], BaseTrapEventType=[INTEGER], EntPhysicalContainedIn=[INTEGER], EntPhysicalName="[OCTET]", Relati
veResource="[OCTET]", ReasonDescription="[OCTET]")
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid 136193   //An alarm indicating a high transmit power of an optical module.
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid 136194   //An alarm indicating a low transmit power of an optical module.
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid 136195   //An alarm indicating a high receive power of an optical module.
ENTITYTRAP_1.3.6.1.4.1.2011.5.25.219.2.4.5 hwOpticalInvalid 136196   //An alarm indicating a low receive power of an optical module.
ENTITYTRAP/3/OPTICALINVALID:OID [oid] Optical Module is invalid.(Index=[INTEGER], EntityPhysicalIndex=[INTEGER], PhysicalName=\"
[OCTET]\", EntityTrapFaultID=[INTEGER])
Possible Causes
  • The type and wavelength of the local and remote optical modules are inconsistent.
  • The optical module is incorrectly installed or the optical fiber is faulty.
  • The fiber is too long or the fiber attenuation is too high.
  • The remote transmit power is out of the allowed range.
  • The optical module is faulty.
Troubleshooting Procedure
NOTE:

You are advised to save the results of each troubleshooting step. This information will help Huawei technical support assist you if the fault persists.

  1. Check whether the local and remote optical modules have the same wavelength.

    Run the display transceiver [ interface interface-type interface-number | slot slot-id ] [ verbose ] command to check optical module information on the interface. The Wavelength(nm) field in the command output indicates the wavelength of an optical module. If the two optical modules have different wavelengths, replace one optical module to ensure that the two optical modules have the same wavelength.

    If the fault persists, go to step 2.

  2. Check the link connection.

    Remove and reinstall the fiber and optical module to ensure they are properly connected. Check whether the fiber connector is dirty or damaged. If so, clean or replace the connector.

    If the fault persists, go to step 3.

  3. Check the fiber length.

    The fiber length must be shorter than the maximum transmission distance of an optical module. For the maximum transmission distance supported by different optical modules, see Pluggable Modules for Interfaces in the hardware description. If the fiber length exceeds the maximum transmission distance of the optical modules, shorten the fiber length or use optical modules with a longer transmission distance.

    If the fault persists, go to step 4.

  4. Check the transmit optical power on the remote device.

    Ensure that the transmit optical power on the remote device exceeds the lower threshold.

    If the fault persists, go to step 5.

  5. Check whether the fiber type matches the optical module.

    Ensure that the fiber type matches the optical module:
    • A multimode fiber, generally distinguished by an orange outer sheath, is used together with a multimode optical module.
    • A single-mode fiber, generally distinguished by a yellow outer sheath, is used with a single-mode optical module.
    If the fault persists, go to step 6.
  6. Check the optical module type and vendor.

    Check whether the local and remote devices use the same type of optical modules from the same vendor. If the connected optical modules have the same wavelength and provide short-distance transmission but alarms indicating low or high optical power occur, the two optical modules may be from different vendors. Although these optical modules have the same wavelength, optical power alarms occur because different vendors design different optical power indicators for these optical modules. To rectify the fault, use optical modules from the same vendor.

    If the fault persists, go to step 7.

  7. Replace the parts.

    Perform a short fiber loopback test. If the fault cannot be located, replace the optical module or fiber.

    If the fault persists, go to step 8.

  8. Collect the following information and contact Huawei technical support:
    • Results of the preceding troubleshooting procedure
    • Configuration file, logs, and alarms of the device

How Can I View Optical Power Information?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain the correct information. You are advised to use Huawei-certified optical modules.

Run the display transceiver interface interface-type interface-number verbose command to view power information of a specified optical module.

<Quidway> display transceiver interface gigabitethernet 3/0/0 verbose
GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------                   
Common information:                                                                                                                 
  Transceiver Type               :GPS_SFP                                                                                           
  Connector Type                 :SMA Coaxial Connector                                                                             
  Wavelength(nm)                 :-                                                                                                 
  Transfer Distance(m)           :100(copper)                                                                                       
  Digital Diagnostic Monitoring  :NO                                                                                                
  Vendor Name                    :HUAWEI                                                                                            
  Vendor Part Number             :HUAWEI AE 905S A                                                                                  
  Ordering Name                  :                                                                                                  
-------------------------------------------------------------
Manufacture information:                                                                                                            
  Manu. Serial Number            :031TUX10HB000065                                                                                  
  Manufacturing Date             :2017-11-28                                                                                        
  Vendor Name                    :HUAWEI                                 
-------------------------------------------------------------                   
Alarm information:                                                              
  TX power low                                                                  
-------------------------------------------------------------                   
Diagnostic information:                                                         
  Temperature(°C)                       :39                                     
  Voltage(V)                            :3.31                                   
  Bias Current(mA)                      :6.59                                   
  Bias High Threshold(mA)               :10.50                                  
  Bias Low  Threshold(mA)               :2.50                                   
  Current Rx Power(dBM)                 :-2.23           //Indicate the current receive power of the optical module.                       
  Default Rx Power High Threshold(dBM)  :3.01            //Indicate the default receive power upper alarm threshold of the optical module.                      
  Default Rx Power Low  Threshold(dBM)  :-15.02          //Indicate the default receive power lower alarm threshold of the optical module.                      
  Current Tx Power(dBM)                 :-2.45           //Indicate the current transmit power of the optical module.                       
  Default Tx Power High Threshold(dBM)  :3.01            //Indicate the default transmit power upper alarm threshold of the optical module.                       
  Default Tx Power Low  Threshold(dBM)  :-9.00           //Indicate the default transmit power lower alarm threshold of the optical module.                       
  User Set Rx Power High Threshold(dBM) :3.01            //Indicate the configured receive power upper alarm threshold of the optical module.                       
  User Set Rx Power Low Threshold(dBM)  :-15.02          //Indicate the configured receive power lower alarm threshold of the optical module.                       
  User Set Tx Power High Threshold(dBM) :3.01            //Indicate the configured transmit power upper alarm threshold of the optical module.                       
  User Set Tx Power Low Threshold(dBM)  :-9.00           //Indicate the configured transmit power lower alarm threshold of the optical module.                       
------------------------------------------------------------- 

The optical power is normal when it is between the upper and lower thresholds. If the optical power exceeds the configured upper threshold, a high optical power alarm is generated. If the optical power falls below the configured lower threshold, a low optical power alarm is generated.

How Can I View the Optical Module Wavelength?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain correct information. You are advised to use Huawei-certified optical modules.

The wavelength of the local and remote ends must be the same. You are advised to use Huawei-certified optical modules of the same type.

Run the display transceiver interface interface-type interface-number command to view the wavelength of a specified optical module.

<Quidway> display transceiver interface gigabitethernet 3/0/0
GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------                   
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
 Wavelength(nm)              :850
  Transfer Distance(m)           :0(9um),300(50um),150(62.5um)                  
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :HUAWEI                              
  Vendor Part Number             :02318169 
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :CD25HP12M                                  
  Manufacturing Date             :2013-06-184                                    
  Vendor Name                    :HUAWEI                                   
-------------------------------------------------------------                   
Alarm information:                                                              
  TX power low                                                                  
-------------------------------------------------------------                   

How Can I View the Optical Module Transmission Distance?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain correct information. You are advised to use Huawei-certified optical modules.

Optical signals sent from different types of sources can transmit over different distances due to negative effects of optical fibers, such as dispersion and attenuation. When connecting optical interfaces, select optical modules and fibers according to the longest signal transmission distance.

Run the display transceiver interface interface-type interface-number command to view the transmission distance of a specified optical module.

<Quidway> display transceiver interface gigabitethernet 3/0/0
GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------                   
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
  Wavelength(nm)                 :850                                           
  Transfer Distance(m)       :0(9um),:300(50um),150(62.5um)                  
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :HUAWEI                              
  Vendor Part Number             :02318169 
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :CD25HP12M                                  
  Manufacturing Date             :2013-06-184                                    
  Vendor Name                    :HUAWEI                                  
-------------------------------------------------------------                   
Alarm information:                                                              
  TX power low                                                                  
-------------------------------------------------------------                   

How Can I View the Temperature, Voltage, and Current of an Optical Module?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain correct information. You are advised to use Huawei-certified optical modules.

Run the display transceiver interface interface-type interface-number verbose command to view the temperature, voltage, and current of a specified optical module.

<Quidway> display transceiver interface gigabitethernet 3/0/0 verbose
GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------
Common information:                                                                                                                 
  Transceiver Type               :GPS_SFP                                                                                           
  Connector Type                 :SMA Coaxial Connector                                                                             
  Wavelength(nm)                 :-                                                                                                 
  Transfer Distance(m)           :100(copper)                                                                                       
  Digital Diagnostic Monitoring  :NO                                                                                                
  Vendor Name                    :HUAWEI                                                                                            
  Vendor Part Number             :HUAWEI AE 905S A                                                                                  
  Ordering Name                  :                                                                                                  
-------------------------------------------------------------
Manufacture information:                                                                                                            
  Manu. Serial Number            :031TUX10HB000065                                                                                  
  Manufacturing Date             :2017-11-28                                                                                        
  Vendor Name                    :HUAWEI 
-------------------------------------------------------------
Alarm information:
  RX loss of signal
  RX power low
-------------------------------------------------------------
Diagnostic information:
  Temperature(°C)                       :33      //Indicate the current temperature of the optical module.
  Voltage(V)                            :3.32    //Indicate the current voltage of the optical module.
  Bias Current(mA)                      :7.31    //Indicate the bias current of the optical module.
  Bias High Threshold(mA)               :10.00   //Indicate the bias current higher threshold of the optical module.
  Bias Low  Threshold(mA)               :2.60    //Indicate the bias current lower threshold of the optical module.
  Current Rx Power(dBM)                 :-29.21
  Default Rx Power High Threshold(dBM)  :1.50
  Default Rx Power Low  Threshold(dBM)  :-14.00
  Current Tx Power(dBM)                 :-1.82
  Default Tx Power High Threshold(dBM)  :-1.00
  Default Tx Power Low  Threshold(dBM)  :-8.00
  User Set Rx Power High Threshold(dBM) :1.50
  User Set Rx Power Low Threshold(dBM)  :-14.00
  User Set Tx Power High Threshold(dBM) :-1.00
  User Set Tx Power Low Threshold(dBM)  :-8.00
-------------------------------------------------------------

Why Can I Not Obtain Optical Module Information?

The following situations may prevent you from obtaining information about an optical module:
  • Non-Huawei-certified optical modules are used.
  • No optical module is installed.
  • The system does not support the query of the temperature, voltage, current, receive power, and transmit power of the optical module.
  • The interface does not have any transmit or receive signal and the power is 0, indicated by the transmit or receive power being NA.
  • The optical module is faulty. Replace the optical module for fault locating.

How Can I Determine Whether an Optical Module Is Single-Mode or Multi-Mode?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain correct information. You are advised to use Huawei-certified optical modules.

Run the display transceiver interface interface-type interface-number command to view information about a specified optical module. You can determine whether an optical module is a single-mode or multi-mode one according to the fiber diameter displayed in the transmission distance. In the following command output, 50 um and 62.5 um are fiber diameters, indicating multi-mode fibers. Fibers with a diameter of 9 um are single-mode fibers.

<Quidway> display transceiver interface gigabitethernet 3/0/0

GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------                   
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
  Wavelength(nm)                 :850                                           
  Transfer Distance(m)       :500(50um),300(62.5um)                         
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :FINISAR CORP.                                 
  Vendor Part Number             :FTLF8519P2BNL-HW                              
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :PEP3L5D                                       
  Manufacturing Date             :2008-12-05                                    
  Vendor Name                    :FINISAR CORP.                                 
-------------------------------------------------------------                   
Alarm information:                                                              
  TX power low                                                                  
-------------------------------------------------------------                   

What Are the MIB OIDs of Optical Module Information?

The following table describes the MIB OIDs of optical module information.

Object Name

OID

Syntax

Description

Max Access

hwEntityOpticalVendorSn

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.4

OCTET STRING

This object indicates the SN of an optical module.

read-only

hwEntityOpticalTemperature

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.5

Integer32

This object indicates the temperature of an optical module, in °C.

read-only

hwEntityOpticalVoltage

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.6

Integer32

This object indicates the voltage of an optical module, in mV.

read-only

hwEntityOpticalBiasCurrent

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.7

Integer32

This object indicates the bias current of an optical module, in uA.

read-only

hwEntityOpticalRxPower

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.8

Integer32

This object indicates the receive power of an optical module, in uW. uW = (10^(dBM/10))*1000.

read-only

hwEntityOpticalTxPower

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.9

Integer32

This object indicates the transmit power of an optical module, in uW.

read-only

hwEntityOpticalVenderPn

1.3.6.1.4.1.2011.5.25.31.1.1.3.1.25

OCTET STRING

This object indicates the PN of an optical module.

read-only

What Does Alarm information Mean in Optical Module Information?

When you run the display transceiver interface interface-type interface-number verbose command to view information about a specified optical module, Alarm information indicates which fault occurs on the optical module. Table 1-2 describes the possible alarms.

<Quidway> display transceiver interface gigabitethernet 3/0/0 verbose
GigabitEthernet3/0/0 transceiver information:                                  
-------------------------------------------------------------                   
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
  Wavelength(nm)                 :850                                           
  Transfer Distance(m)           :500(50um),300(62.5um)                         
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :FINISAR CORP.                                 
  Vendor Part Number             :FTLF8519P2BNL-HW                              
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :PEP3L5D                                       
  Manufacturing Date             :2008-12-05                                    
  Vendor Name                    :FINISAR CORP.                                 
-------------------------------------------------------------                   
Alarm information:                                                              
  TX power low                                                                  
-------------------------------------------------------------                   
Diagnostic information:                                                         
  Temperature(°C)                       :39                                     
  Voltage(V)                            :3.31                                   
  Bias Current(mA)                      :6.59                                   
  Bias High Threshold(mA)               :10.50                                  
  Bias Low  Threshold(mA)               :2.50                                   
  Current Rx Power(dBM)                 :-2.23         
  Default Rx Power High Threshold(dBM)  :3.01                     
  Default Rx Power Low  Threshold(dBM)  :-15.02                     
  Current Tx Power(dBM)                 :-2.45            
  Default Tx Power High Threshold(dBM)  :3.01                   
  Default Tx Power Low  Threshold(dBM)  :-9.00                      
  User Set Rx Power High Threshold(dBM) :3.01                     
  User Set Rx Power Low Threshold(dBM)  :-15.02                       
  User Set Tx Power High Threshold(dBM) :3.01                          
  User Set Tx Power Low Threshold(dBM)  :-9.00          
------------------------------------------------------------- 
Table 1-2  Alarm information and meaning

Alarm

Meaning

TX fault

A transmission fault occurs.

RX loss of signal

Received signals are lost.

Transceiver info I/O error

Module information read and write error occurs.

Transceiver info checksum error

Module information checksum is incorrect.

Transceiver type not supported by port hardware

An interface does not support the module type.

Temp high

The temperature is high.

Temp low

The temperature is low.

Voltage high

The voltage is high.

Voltage low

The voltage is low.

TX bias high

The bias current is high.

TX bias low

The bias current is low.

TX power high

The transmit power is high.

TX power low

The transmit power is low.

RX power high

The receive power is high.

RX power low

The receive power is low.

How Can I View the Optical Attenuation?

The optical attenuation information cannot be viewed directly. You need to view the current optical power in optical module information to determine whether the optical power is attenuated.

How Can I Determine Whether an Interface Has an Optical Module?

NOTE:

If non-Huawei-certified optical modules are used, the system may be unable to obtain correct information. You are advised to use Huawei-certified optical modules.

Run the display transceiver command to view optical module information.
<Quidway> display transceiver                                                                                                        
                                                                                                                                    
GigabitEthernet3/1/12 transceiver information:                                                                                      
-------------------------------------------------------------                                                                       
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
  Wavelength(nm)                 :850                                           
  Transfer Distance(m)           :0(9um),300(50um),150(62.5um)                  
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :HUAWEI                              
  Vendor Part Number             :02318169 
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :CD25HP12M                                  
  Manufacturing Date             :2013-06-184                                    
  Vendor Name                    :HUAWEI                                                                                              
-------------------------------------------------------------                                                                       
Alarm information:                                                                                                                  
  RX loss of signal                                                                                                                 
-------------------------------------------------------------                                                                       
                                                                                                                                    
GigabitEthernet3/1/13 transceiver information:                                                                                      
-------------------------------------------------------------                                                                       
Common information:                                                             
  Transceiver Type               :1000_BASE_SX_SFP                              
  Connector Type                 :LC                                            
  Wavelength(nm)                 :850                                           
  Transfer Distance(m)           :0(9um),300(50um),150(62.5um)                  
  Digital Diagnostic Monitoring  :YES                                           
  Vendor Name                    :HUAWEI                              
  Vendor Part Number             :02318169 
  Ordering Name                  :                                              
-------------------------------------------------------------                   
Manufacture information:                                                        
  Manu. Serial Number            :CD25HP12M                                  
  Manufacturing Date             :2013-06-184                                    
  Vendor Name                    :HUAWEI                                                                                            
-------------------------------------------------------------                                                                       
Alarm information:                                                                                                                  
  RX loss of signal                                                                                                                 
-------------------------------------------------------------  
Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 38204

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next