No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the Fabric Mode

Configuring the Fabric Mode

Context

The actual forwarding capability of an LPU depends on the amount of bandwidth resources allocated to it by the SRU. An LPU can forward data at line speed only when it has sufficient bandwidth resources. An SRU provides limited bandwidth resources. In common fabric mode, the SRU allocates equal amounts of bandwidth resources to each LPU. The allocated bandwidth resources are sufficient for line-speed forwarding on most LPUs but cannot support line-speed forwarding on some high-performance LPUs. When these high-performance LPUs cannot realize line-speed forwarding, their forwarding capabilities are wasted.

A device supports extended fabric mode of the SRU. In this mode, LPUs in slot 6 and slot 7 can obtain more bandwidth resources to ensure line-speed forwarding.

NOTE:

Only S9312 and S9312E support this function.

In common fabric mode, the following LPUs cannot realize line-speed forwarding:
  • LE2D2X48SEC0 (S9312E)
  • LE0DX12XSA00 (S9312E, S9312)
  • LE2D2X08SED4/LE2D2X08SED5 (S9312E, S9312)
  • LE0DX40SFC00 (S9312E, S9312)
  • LE0DX16SFC00 (S9312E, S9312)
  • LE1D2X32SSC0 (S9312E, S9312)
  • LE1D2C02FEE0 (S9312E, S9312)
  • LE1D2X32SEC0 (S9312E, S9312)
  • LE1D2H02QEC0 (S9312E, S9312)
  • X2E series (S9312E, S9312)
  • X2H series (S9312E, S9312)
  • X2S series (S9312E, S9312)

Pre-configuration Tasks

Before configuring the fabric mode on an S9312E switch, ensure that the switch is equipped with an LH2D2SRUDC00/LE2D2SRUDC01 main control unit.

Before configuring the fabric mode on an S9312 switch, ensure that the switch is equipped with an LE1D2SRUH000/LE1D2SRUH002 main control unit.

Procedure

  1. (Optional) Run display fabric-mode configuration

    The fabric mode configuration is displayed.

  2. Run system-view

    The system view is displayed.

  3. Run set fabric-mode turbo [ all | chassis chassis-id ]

    The extended fabric mode is configured.

    By default, the S9312 chassis with SWC02BAKG000 or SWC02BAKR000 backplane uses the common fabric mode, and other S9312 chassis models use the extended fabric mode. For the S9312E, the common fabric mode is used by default.

Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 43729

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next