No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Software and Hardware Support for S9300 CSS Card Clustering

Software and Hardware Support for S9300 CSS Card Clustering

Table 3-5  Software and Hardware Support for S9306&S9312 CSS Card Clustering

Device Model

  • S9306

  • S9312

CSS Card and Installation Slot

CSS card: LE0D0VSTSA00 (All ports on the CSS cards must be connected.)

Installation slot: subcard slots of LE0MSRUA (non-VER.A), LE0DSRUA, and LE0D00SRUB00 (non-VER.A)

CSS card and MPU models are abbreviated to VSTSA and SRUA (or SRUB) respectively.

CSS card: LE1D2VS04000 (CSS ports on the CSS cards must have at least one cable connected and ports on both ends of the cable must use the same port number.)

Installation slot: subcard slots of LE1D2SRUH000, LE1D2SRUH002, and LE1D2SRUE000

CSS card and MPU models are abbreviated to VS04 and SRUH (or SRUE) respectively.

Software Version

V100R003C00 and later versions

SRUH: V200R009C00 and later versions

SRUE: V200R010C00 and later versions

Hot Swap of CSS Cards

Not supported Supported

Number of CSS Cards Supported by Each Chassis

2 2

Number of CSS Ports on Each CSS Card and Bandwidth of a Single CSS Port

Four 16G ports Four 10G ports

Pluggable Modules for Ports on CSS Cards

  • 3 m and 10 m QSFP+ high-speed cables

  • QSFP+ optical module (except the QSFP-40G-SR-BD model) and fiber

  • 10 m QSFP+ AOC cable (supported since V200R010C00)

  • 5 m QSFP+ high-speed cables (supported since V200R011C10)
  • 1 m, 3 m, 5 m (passive), and 10 m (active) SFP+ cables

  • SFP+ optical module and fiber

  • 3 m and 10 m SFP+ AOC cables

Hardware Configuration

  • Two S9306s, one S9306 and one S9312, or two S9312s can set up a CSS.
  • Each chassis must have both active and standby MPUs installed, and the two MPUs must have stack cards installed.

  • MPUs in a single chassis must be the same model. Two chassis with different SRUs can set up a CSS only in one case: SRUA in one chassis and SRUB in the other.

  • Two S9306s, one S9306 and one S9312, or two S9312s can set up a CSS.
  • Each chassis can have only one SRU installed, and a CSS card can be installed in any MPU slot. To ensure reliability, you are advised to install two MPUs in each chassis.

  • MPUs in a single chassis must be the same model. Two chassis with different SRUs can set up a CSS only in one case: SRUH in one chassis and SRUE in the other and both chassis run V200R010C00 or a later version.

License Required

No

Table 3-6  Software and Hardware Support for S9310 CSS Card Clustering

Device Model

S9310

CSS Card and Installation Slot

CSS cards are integrated into MPUs (LE1D2SRUKC00 and LE1D2SRUKC01) and do not need to be installed.

CSS cards are integrated into SFUs (LE1D2SFUK000) and do not need to be installed.

MPU and SFU models are abbreviated to SRUK and SFUK respectively.

Software Version

V200R010C00 and later versions

Number of CSS Cards Supported by Each Chassis

4

Number of CSS Ports on Each CSS Card and Bandwidth of a Single CSS Port

Four 10G ports and one 40G port

Pluggable Modules for Ports on CSS Cards

10G port:
  • 1 m, 3 m, 5 m (passive), and 10 m (active) SFP+ cables

  • SFP+ optical module and fiber

  • 3 m and 10 m SFP+ AOC cables

40G port:
  • 1 m, 3 m, and 5 m QSFP+ high-speed cables
  • QSFP+ optical module (except the QSFP-40G-SR-BD model) and fiber
  • 10 m QSFP+ AOC cable (this cable cannot be used when 40G ports on both ends are split into 10G ports)

Hardware Configuration

  • Two S9310s can set up a CSS.
  • Each chassis can have only one MPU installed. It is recommended that each chassis have two MPUs installed. If 1+N backup of MPUs is required so that a CSS can operate normally even if two MPUs in one chassis are faulty, SFUs also need to be installed.

License Required

No
Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 38183

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next