No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Establishing a CSS (Using CSS Cards)

Example for Establishing a CSS (Using CSS Cards)

Networking Requirements

An enterprise needs to build a network that has a reliable core layer and simple structure to facilitate configuration and management.

In Figure 3-36, SwitchA and SwitchB at the core layer set up a CSS through CSS card connections. SwitchA and SwitchB are the master switch and standby switch respectively. Switches at the aggregation layer connect to the CSS through Eth-Trunks and the CSS connects to the upstream network through an Eth-Trunk. In this example, the core switches are the S9306 switches.

Figure 3-36  Establishing a CSS

Configuration Roadmap

The configuration roadmap is as follows:

  1. Install CSS cards on SwitchA and SwitchB, and connect cluster cables.
  2. Set the connection mode to CSS card connection on SwitchA and SwitchB, and set their CSS IDs and priorities to 1 and 2, 100 and 10 respectively so SwitchA has a higher probability to be the master switch.
  3. Enable the CSS function on SwitchA and then on SwitchB to ensure that SwitchA becomes the master switch.
  4. Check whether a CSS has been established successfully.
  5. Configure downlink Eth-Trunks for the CSS to improve forwarding bandwidth and reliability. (The detailed configuration is omitted in this example. For details about how to configure Eth-Trunks, see Example for Configuring Cluster Eth-Trunks.)

Procedure

  1. Install hardware.

    Install CSS cards on SwitchA and SwitchB, and connect cluster cables. For details about how to install the hardware, see Installing Hardware and Connecting Cluster Cables.

  2. Configure the CSS ID, CSS priority, and CSS connection mode for SwitchA and SwitchB.

    # Set the CSS ID, CSS priority, and CSS connection mode to 1, 100, and CSS card connection for SwitchA.

    <Quidway> system-view
    [Quidway] sysname SwitchA
    [SwitchA] set css mode css-card
    [SwitchA] set css id 1
    [SwitchA] set css priority 100
    

    # Set the CSS ID, CSS priority, and CSS connection mode to 2, 10, and CSS card connection for SwitchB.

    <Quidway> system-view
    [Quidway] sysname SwitchB
    [SwitchB] set css mode css-card
    [SwitchB] set css id 2
    [SwitchB] set css priority 10
    
    NOTE:

    To use two S9310s or S9310Xs to establish a CSS, you need to run the css port media-type command to set the CSS port type to the actual port type used for cluster connections. You can run the display css status [ saved ] command to check the current and saved CSS port types based on the CSS port media-type field.

    # Check the CSS configuration.

    NOTE:

    After the configuration is complete, run the display css status saved command to check the CSS configuration.

    # Check the CSS configuration on SwitchA.

    [SwitchA] display css status saved
    Current Id   Saved Id     CSS Enable   CSS Mode    Priority    Master force     
    ------------------------------------------------------------------------------  
    1            1            Off          CSS card    100         Off             

    # Check the CSS configuration on SwitchB.

    [SwitchB] display css status saved
    Current Id   Saved Id     CSS Enable   CSS Mode    Priority    Master force     
    ------------------------------------------------------------------------------  
    1            2            Off          CSS card    10          Off              

  3. Enable the CSS function.

    # Enable the CSS function on SwitchA and restart SwitchA.

    [SwitchA] css enable
    Warning: The CSS configuration will take effect only after the system is rebooted. T
    he next CSS mode is CSS card. Reboot now? [Y/N]:y

    # Enable the CSS function on SwitchB and restart SwitchB.

    [SwitchB] css enable
    Warning: The CSS configuration will take effect only after the system is rebooted. T
    he next CSS mode is CSS card. Reboot now? [Y/N]:y

  4. Check whether a CSS has been established successfully.

    # View the indicator status.

    If the MASTER indicator on a CSS card of SwitchA is steady on, the MPU with the CSS card installed is the master MPU and SwitchA is the master switch.

    If the MASTER indicator on a CSS card of SwitchB is off, SwitchB is the standby switch.

    # Log in to the CSS through the console port on any MPU to check whether the CSS has been established successfully.

    <SwitchA> display device
    Chassis 1 (Master Switch)                                                       
    S9306's Device status:                                                          
    Slot  Sub Type         Online    Power      Register       Status     Role
    - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
    1     -   LE0DT24XEA00 Present   PowerOn    Registered     Normal     NA    
    2     -   LE0MG48SC    Present   PowerOn    Registered     Normal     NA    
    7     -   LE0D00SRUB00 Present   PowerOn    Registered     Normal     Master
          1   LE0D0VSTSA00 Present   PowerOn    Registered     Normal     NA    
    8     -   LE0D00SRUB00 Present   PowerOn    Registered     Normal     Slave 
          1   LE0D0VSTSA00 Present   PowerOn    Registered     Normal     NA    
    PWR1  -   -            Present   PowerOn    Registered     Normal     NA    
    CMU1  -   LE0DCMUA0000 Present   PowerOn    Registered     Normal     Slave 
    CMU2  -   LE0DCMUA0000 Present   PowerOn    Registered     Normal     Master
    FAN1  -   -            Present   PowerOn    Registered     Normal     NA    
    FAN2  -   -            Present   PowerOn    Registered     Normal     NA    
    Chassis 2 (Standby Switch)                                                      
    S9306's Device status:                                                          
    Slot  Sub Type         Online    Power      Register       Status     Role
    - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
    1     -   LE0DG48SBC00 Present   PowerOn    Registered     Normal     NA    
    3     -   LE0MF48TA    Present   PowerOn    Registered     Normal     NA    
    5     -   LE0MF48TC    Present   PowerOn    Registered     Normal     NA    
    6     -   LE0MG48SD    Present   PowerOn    Registered     Normal     NA    
    7     -   LE0D00SRUB00 Present   PowerOn    Registered     Normal     Master
          1   LE0D0VSTSA00 Present   PowerOn    Registered     Normal     NA    
    8     -   LE0D00SRUB00 Present   PowerOn    Registered     Normal     Slave 
          1   LE0D0VSTSA00 Present   PowerOn    Registered     Normal     NA    
    PWR1  -   -            Present   PowerOn    Registered     Normal     NA    
    CMU1  -   LE0DCMUA0000 Present   PowerOn    Registered     Normal     Master
    FAN1  -   -            Present   PowerOn    Registered     Normal     NA    
    FAN2  -   -            Present   PowerOn    Registered     Normal     NA    
    

    If the command output displays card status of both member switches, the CSS has been established successfully.

    # Check whether the CSS links are normal.

    <SwitchA> display css channel
                    Chassis 1               ||               Chassis 2              
    ================================================================================
    Num [SRUB HG]    [VSTS Port(Status)]    ||    [VSTS Port(Status)]    [SRUB HG]  
    1   1/7  1/15 -- 1/7/0/1(UP 16G)     ---||--- 2/7/0/4(UP 16G)     -- 2/8  1/14  
    2   1/7  0/15 -- 1/7/0/3(UP 16G)     ---||--- 2/8/0/2(UP 16G)     -- 2/7  0/14  
    3   1/7  1/14 -- 1/8/0/4(UP 16G)     ---||--- 2/7/0/1(UP 16G)     -- 2/7  1/15  
    4   1/7  0/14 -- 1/8/0/2(UP 16G)     ---||--- 2/8/0/3(UP 16G)     -- 2/8  0/15  
    5   1/8  1/15 -- 1/8/0/1(UP 16G)     ---||--- 2/8/0/4(UP 16G)     -- 2/7  1/14  
    6   1/8  0/15 -- 1/8/0/3(UP 16G)     ---||--- 2/7/0/2(UP 16G)     -- 2/8  0/14  
    7   1/8  1/14 -- 1/7/0/4(UP 16G)     ---||--- 2/8/0/1(UP 16G)     -- 2/8  1/15  
    8   1/8  0/14 -- 1/7/0/2(UP 16G)     ---||--- 2/7/0/3(UP 16G)     -- 2/7  0/15  

    If all the CSS links are in Up state, the CSS has been established successfully.

  5. Configure downlink Eth-Trunks for the CSS. (The detailed configuration is not provided here.)

Configuration Files

None

Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 37113

Downloads: 15

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next