No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring MAD in Direct Mode

Example for Configuring MAD in Direct Mode

Networking Requirements

In Figure 3-39, SwitchA and SwitchB set up a CSS.

If a CSS splits due to a CSS link failure, the network has two CSS systems with conflicting configurations. To avoid this situation, configure the MAD function in the CSS. This function minimizes the impact of a CSS split on the network.

Figure 3-39  MAD in direct mode

Configuration Roadmap

The configuration roadmap is as follows:
  1. Configure MAD in direct mode on a specified port.

Procedure

  1. Configure MAD in direct mode on a specified port.

    # Configure MAD in direct mode on GigabitEthernet1/2/0/0.

    <Quidway> system-view
    [Quidway] interface gigabitethernet 1/2/0/0
    [Quidway-GigabitEthernet1/2/0/0] mad detect mode direct
    Warning: This command will block the port, and no other configuration running on
     this  port is recommended. Continue?[Y/N]:y
    [Quidway-GigabitEthernet1/2/0/0] quit

    # Configure MAD in direct mode on GigabitEthernet2/10/0/0.

    [Quidway] interface gigabitethernet 2/10/0/0
    [Quidway-GigabitEthernet2/10/0/0] mad detect mode direct
    Warning: This command will block the port, and no other configuration running on
     this  port is recommended. Continue?[Y/N]:y
    [Quidway-GigabitEthernet2/10/0/0] quit
    [Quidway] quit

  2. Verify the configuration.

    # Check detailed MAD configuration of the CSS.

    <Quidway> display mad verbose
    Current MAD domain: 0
    Current MAD status: Detect
    Mad direct detect interfaces configured:
     GigabitEthernet1/2/0/0
     GigabitEthernet2/10/0/0
    Mad relay detect interfaces configured:
    Excluded ports(configurable):
    Excluded ports(can not be configured):
     40GE1/4/0/0
     40GE1/4/0/1
     40GE1/5/0/0
     40GE1/5/0/1
     40GE2/7/0/1
     40GE2/7/0/0
     40GE2/11/0/0
     40GE2/11/0/1 

  3. Verify the MAD function.

    When the MAD function is configured and no services are deployed in the CSS, manually split the CSS to verify whether the MAD configuration takes effect.

    1. Check information about all the Up ports in the CSS. Based on the displayed information, verify the MAD function after the CSS splits.

      <Quidway> display interface brief | include up 
      PHY: Physical
      *down: administratively down
      ^down: standby
      (l): loopback
      (s): spoofing
      (E): E-Trunk down
      (b): BFD down
      (e): ETHOAM down
      (dl): DLDP down
      (d): Dampening Suppressed
      InUti/OutUti: input utility/output utility
      Interface                   PHY   Protocol  InUti OutUti   inErrors  outErrors
      Ethernet0/0/0/0             up    up        0.03%  0.01%          0          0
      GigabitEthernet1/2/0/0      up    up           0%     0%          0          0
      GigabitEthernet1/2/0/5      up    up           0%     0%          0          0
      GigabitEthernet2/9/0/5      up    up           0%     0%          0          0
      GigabitEthernet2/10/0/0     up    up           0%     0%          0          0
      NULL0                       up    up(s)        0%     0%          0          0
      40GE1/4/0/0                 up    up           0%     0%          0          0
      40GE1/4/0/1                 up    up           0%     0%          0          0
      40GE1/5/0/0                 up    up           0%     0%          0          0
      40GE1/5/0/1                 up    up           0%     0%          0          0
      40GE2/7/0/0                 up    up           0%     0%          0          0
      40GE2/7/0/1                 up    up           0%     0%          0          0
      40GE2/11/0/0                up    up           0%     0%          0          0
      40GE2/11/0/1                up    up           0%     0%          0          0

    2. Enable the alarm function in the user view.

      <Quidway> terminal monitor
      <Quidway> terminal trapping

    3. Make the CSS split by shutting down all CSS member ports or removing all cluster cables. (The following procedure shuts down all the CSS member ports in a CSS that is set up in service port connection mode.)

      # Check information about the service ports used for CSS connections.

      <Quidway> display css css-port all
      B : broadcast   *down : administratively down
      Logic Port          Num  Phy Port                      Status
         css-port1/1      2    40GE1/4/0/0                   up
                               40GE1/4/0/1                   up
      (B)css-port1/2      2    40GE1/5/0/0                   up
                               40GE1/5/0/1                   up
      
      Logic Port          Num  Phy Port                      Status
         css-port2/1      2    40GE2/7/0/1                   up
                               40GE2/7/0/0                   up
      (B)css-port2/2      2    40GE2/11/0/0                  up
                               40GE2/11/0/1                  up

      # Shut down CSS ports.

      <Quidway> system-view
      [Quidway] interface css-port 1/1
      [Quidway-css-port1/1] shutdown interface 40GE1/4/0/0
      [Quidway-css-port1/1] shutdown interface 40GE1/4/0/1
      [Quidway-css-port1/1] quit
      [Quidway] interface css-port 1/2
      [Quidway-css-port1/2] shutdown interface 40GE1/5/0/0
      [Quidway-css-port1/2] shutdown interface 40GE1/5/0/1
      Warning: Shutting down the last active CSS port in master chassis will cause CSS split, Continue? [Y/N]:y
      [Quidway-css-port1/2] return

    4. Check whether the following alarm is displayed on the terminal screen: MAD/4/MULTIACTIVEDETECTED(t):OID 1.3.6.1.4.1.2011.5.25.246.1.1 Multi-active scenario is detected.
    5. Check the CSS status, MAD information, and port status.

      # Check the CSS status. The command output shows that the two-chassis CSS has changed into a single-chassis CSS.

      <Quidway> display css status
      CSS Enable switch On
      
      Chassis Id   CSS Enable   CSS Status      CSS Mode    Priority    Master Force
      ------------------------------------------------------------------------------
      1            On           Single         LPU           100         Off

      # Check MAD information in the current CSS (chassis 1). The command output shows that the MAD status is Detect.

      <Quidway> display mad verbose
      Current MAD domain: 0
      Current MAD status: Detect
      Mad direct detect interfaces configured:
       GigabitEthernet1/2/0/0
      Mad relay detect interfaces configured:
      Excluded ports(configurable):
      Excluded ports(can not be configured):
       40GE1/4/0/0
       40GE1/4/0/1
       40GE1/5/0/0
       40GE1/5/0/1 

      # Check information about Up ports in the current CSS (chassis 1). The command output shows that the status of common service ports remains unchanged.

      <Quidway> display interface brief | include up
      PHY: Physical
      *down: administratively down
      ^down: standby
      (l): loopback
      (s): spoofing
      (E): E-Trunk down
      (b): BFD down
      (e): ETHOAM down
      (dl): DLDP down
      (d): Dampening Suppressed
      InUti/OutUti: input utility/output utility
      Interface                   PHY   Protocol  InUti OutUti   inErrors  outErrors
      Ethernet0/0/0/0             up    up        0.01%  0.01%          0          0
      GigabitEthernet1/2/0/5      up    up           0%     0%          0          0
      NULL0                       up    up(s)        0%     0%          0          0

    6. Log in to chassis 2 through its serial port.

      # Check MAD information in chassis 2. The command output shows that the MAD status is Recovery.

      <Quidway> display mad verbose
      Current MAD domain: 0
      Current MAD status: Recovery
      Mad direct detect interfaces configured:
       GigabitEthernet2/10/0/0
      Mad relay detect interfaces configured:
      Excluded ports(configurable):
      Excluded ports(can not be configured):
       40GE2/7/0/1
       40GE2/7/0/0
       40GE2/11/0/0
       40GE2/11/0/1 

      # Check information about Up ports in chassis 2. The command output shows that all ports in this chassis are Down.

      <Quidway> display interface brief | include up
      PHY: Physical
      *down: administratively down
      ^down: standby
      (l): loopback
      (s): spoofing
      (E): E-Trunk down
      (b): BFD down
      (e): ETHOAM down
      (dl): DLDP down
      (d): Dampening Suppressed
      InUti/OutUti: input utility/output utility
      Interface                   PHY   Protocol  InUti OutUti   inErrors  outErrors
      NULL0                       up    up(s)        0%     0%          0          0 

    7. The preceding operations verify that the MAD function has been configured successfully.
    8. Restore all CSS member ports to the Up state or install cluster cables to the ports, and then configure services.

Configuration Files

#
interface GigabitEthernet1/2/0/0
 mad detect mode direct
#
interface GigabitEthernet2/10/0/0
 mad detect mode direct
#
return
Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 41930

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next