No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Device Management

S9300, S9300E, and S9300X V200R012C00

This document describes the configurations of Device Management, including device status query, hardware management, CSS, SVF, PoE, OPS, OIDS, energy-saving management, information center, fault management, NTP, synchronous ethernet, PTP.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Example for Configuring Clock Synchronization Through Unicast UDP-Encapsulated PTP Messages in Pdelay Mechanism

Example for Configuring Clock Synchronization Through Unicast UDP-Encapsulated PTP Messages in Pdelay Mechanism

Networking Requirements

As shown in Figure 13-18, the bearer network is a Layer 3 network, on which wireless services between NodeBs are transmitted. All devices on the bearer network support PTP. PE1 and PE2 receive clock signals from two different BITS servers to back up each other. When one BITS server fails, clock synchronization on the bearer network is not affected. NodeB2 does not support PTP but supports synchronous Ethernet for frequency synchronization. NodeB1 and NodeB3 support PTP.

Configure PTP on the bearer network to implement frequency synchronization between NodeBs and bearer network devices. This configuration allows PTP-supporting NodeBs to synchronize with bearer network devices.

Figure 13-18  Networking diagram for configuring clock synchronization through unicast UDP-encapsulated PTP messages in Pdelay mechanism

Device Name

Interface

VLANIF Interface

IP Address

Interface MAC Address

PE1

GigabitEthernet1/0/0

VLANIF10

10.0.0.1/24

0000-1111-1111

PE1

GigabitEthernet1/0/1

VLANIF11

10.1.0.1/24

0000-1111-1111

PE2

GigabitEthernet1/0/0

VLANIF10

10.0.0.2/24

0000-1111-2222

PE2

GigabitEthernet1/0/1

VLANIF12

10.2.0.1/24

0000-1111-2222

CE1

GigabitEthernet1/0/0

VLANIF11

10.1.0.2/24

2222-2222-1111

CE1

GigabitEthernet1/0/1

VLANIF13

10.3.0.1/24

2222-2222-1111

CE2

GigabitEthernet1/0/0

VLANIF12

10.2.0.2/24

2222-2222-3333

CE2

GigabitEthernet1/0/1

VLANIF15

10.5.0.1/24

2222-2222-3333

NodeB1

-

VLANIF13

10.3.0.2/24

2222-3333-1111

NodeB3

-

VLANIF15

10.5.0.2/24

2222-3333-2222

Configuration Roadmap

The configuration roadmap is as follows:

  1. Configure a routing protocol to ensure that devices can communicate with each other.

  2. Configure PE1 and PE2 to receive BITS clock signals through BITS interfaces.
  3. Configure the type of devices on the bearer network as BC and configure NodeB2 that does not support PTP to transmit frequency signals through synchronous Ethernet.
  4. Configure PE1 and PE2 as system master clocks and connect them to BITS clocks. PE1 and PE2 back up each other.

  5. Configure unicast UDP encapsulation for PTP messages and set the delay measurement mechanism to Pdelay because IP addresses of interfaces are known.

Procedure

  1. Configure IP addresses for interfaces to enable devices to communicate.
  2. Configure PE1 and PE2 to receive BITS clock signals through BITS interfaces.

    For configuration details, see Example for Configuring the BITS as the Master Clock Source of PTP.

  3. Enable PTP globally on PE1 and configure PE1 as a BC.

    <Quidway> system-view
    [Quidway] sysname PE1
    [PE1] ptp enable
    [PE1] ptp device-type bc
    

  4. Enable PTP frequency synchronization on PE1.

    [PE1] clock source ptp synchronization enable
    

  5. Configure PTP on GigabitEthernet1/0/1 and GigabitEthernet1/0/0 of PE1.

    [PE1] interface gigabitethernet 1/0/1
    [PE1-GigabitEthernet1/0/1] ptp delay-mechanism pdelay
    [PE1-GigabitEthernet1/0/1] ptp udp-egress source-ip 10.1.0.1 destination-ip 10.1.0.2
    [PE1-GigabitEthernet1/0/1] ptp udp-egress destination-mac 2222-2222-1111
    [PE1-GigabitEthernet1/0/1] ptp enable
    [PE1-GigabitEthernet1/0/1] quit
    [PE1] interface gigabitethernet 1/0/0
    [PE1-GigabitEthernet1/0/0] ptp delay-mechanism pdelay
    [PE1-GigabitEthernet1/0/0] ptp udp-egress source-ip 10.0.0.1 destination-ip 10.0.0.2
    [PE1-GigabitEthernet1/0/0] ptp udp-egress destination-mac 0000-1111-2222
    [PE1-GigabitEthernet1/0/0] ptp enable
    [PE1-GigabitEthernet1/0/0] quit
    [PE1] quit

  6. According to the configuration of PE1, configure PE2, CE1, and CE2 based on the IP addresses and MAC addresses of interfaces.
  7. Verify the configuration.

    # Run the display ptp all command to check the PTP running status, including the PTP interface status and clock source ID.

    <CE1> display ptp all
    Device config info
      ------------------------------------------------------------------
      PTP state         :enabled    Domain  value      :0
      Slave only        :no         Device type        :BC
      Static BMC        :no         Local clock ID     :001882fffe1b1235
      PTP freq-sync     :yes        Time lock success  :yes                         
      PTP acl           :no                                                         
    
      BMC run info
      ------------------------------------------------------------------
      Grand clock ID    :001882fffe77c2cf
      Receive number    :GigabitEthernet1/0/0
      Parent clock ID   :001882fffe1b1bf4
      Parent portnumber :1024
      Priority1         :128        Priority2          :128
      Step removed      :1          Clock accuracy     :32
      Clock class       :6          Time Source        :32
      UTC Offset        :0          UTC Offset Valid   :False
      Time Scale        :PTP        Time Traceable     :True
      Leap              :None       Frequence Traceable:True
    
      Port info
      Name                  State        Delay-mech Ann-timeout Type Domain
      ------------------------------------------------------------------------
      GigabitEthernet1/0/0  slave        pdelay     9          BC   0
    
      Clock source info
      Clock Pri1 Pri2 Accuracy Class TimeSrc Signal Switch Direction In-Status
      ------------------------------------------------------------------------
      local 128  128  0x31     187   0xa0     -      -      -         -
      bits0 128  128  0x20       6   0x20     none   off   -/-        abnormal
      bits1 128  128  0x20       6   0x20     none   off   -/-        abnormal

Configuration File

  • CE1 configuration file

    #
    sysname CE1
    #
    ptp enable
    ptp device-type bc
    clock source ptp synchronization enable
    #
    interface GigabitEthernet1/0/0
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.1.0.2 destination-ip 10.1.0.1
     ptp udp-egress destination-mac 0000-1111-1111
     ptp enable
    #
    interface GigabitEthernet1/0/1
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.3.0.1 destination-ip 10.3.0.2
     ptp udp-egress destination-mac 2222-3333-1111
     ptp enable
    #
    return  
  • CE2 configuration file

    #
    sysname CE2
    #
    ptp enable
    ptp device-type bc
    clock source ptp synchronization enable
    #
    interface GigabitEthernet1/0/0
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.2.0.2 destination-ip 10.2.0.1
     ptp udp-egress destination-mac 0000-1111-2222
     ptp enable
    #
    interface GigabitEthernet1/0/1
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.5.0.1 destination-ip 10.5.0.2
     ptp udp-egress destination-mac 2222-3333-2222
     ptp enable
    #
    return
  • PE1 configuration file

    #
    sysname PE1
    #
    clock bits-type 1pps-tod in bits0
    #
    ptp enable
    ptp device-type bc
    clock source ptp synchronization enable
    ptp clock-source bits0 on
    #
    interface GigabitEthernet1/0/0
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.0.0.1 destination-ip 10.0.0.2
     ptp udp-egress destination-mac 0000-1111-2222
     ptp enable
    #
    interface GigabitEthernet1/0/1
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.1.0.1 destination-ip 10.1.0.2
     ptp udp-egress destination-mac 2222-2222-1111
     ptp enable
    #
    return
  • PE2 configuration file

    #
    sysname PE2
    #
    clock bits-type 1pps-tod in bits0
    #
    ptp enable
    ptp device-type bc
    clock source ptp synchronization enable
    ptp clock-source bits0 on
    #
    interface GigabitEthernet1/0/0
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.0.0.2 destination-ip 10.0.0.1
     ptp udp-egress destination-mac 0000-1111-1111
     ptp enable
    #
    interface GigabitEthernet1/0/1
     ptp delay-mechanism pdelay
     ptp udp-egress source-ip 10.2.0.1 destination-ip 10.2.0.2
     ptp udp-egress destination-mac 2222-2222-3333
     ptp enable
    #
    return
Translation
Download
Updated: 2018-09-03

Document ID: EDOC1100038289

Views: 43545

Downloads: 15

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next