No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X V200R012C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for MAC Address Tables

Licensing Requirements and Limitations for MAC Address Tables

Involved Network Elements

Other network elements are not required.

Licensing Requirements

The MAC address table is a basic feature of a switch and is not under license control.

Version Requirements

Table 2-6  Products and versions supporting MAC

Product

Product Model

Software Version

S9300

S9303, S9306, S9312

V100R002, V100R003, V100R006(C00&C01), V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300

S9310

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300X

S9310X

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300E

S9303E, S9306E, S9312E

V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • Dynamic MAC address entries can be learned on an interface only after the interface is added to an existing VLAN.
  • Among existing MAC address entries, only MAC addresses of the dynamic type can be overwritten as MAC addresses of other types.

  • Each static MAC address entry can have only one outbound interface.
  • LE2D2L16QX2H and LE2D2C08HX2H do not support aging of the MAC address entry of which the destination MAC address of packets is matched in mac-fib or enhanced-mac mode.
  • When the aging time of dynamic MAC address entries is set to 0, dynamic MAC address entries do not age. To age MAC address entries, delete the aging time configuration.
  • When MAC address learning is disabled in a VLAN and an interface in the VLAN (excluding LE1D2S04SEC0, LE1D2X32SEC0, and LE1D2H02QEC0 cards, and X series cards) and the discard action is configured for the interface, the interface does not discard packets from this VLAN. For example, MAC address learning is disabled in VLAN 2 but enabled in VLAN 3; Port1 in VLAN 2 and VLAN 3 has MAC address learning disabled and the discard action is defined. In this situation, Port1 discards packets from VLAN 3 but forwards packets from VLAN 2.
  • When the interface frequently alternates between Up and Down, MAC address entries may be not aged within two aging period. At this time, you are advised to check the link quality or run the port link-flap protection enable command to configure link flapping protection.
Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038290

Views: 100721

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next