No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X V200R012C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VLANs

Licensing Requirements and Limitations for VLANs

Involved Network Elements

Other network elements are not required.

Licensing Requirements

VLAN is a basic feature of a switch and is not under license control.

Version Requirements

Table 4-5  Products and versions supporting VLANs

Series

Products

Software Version

S9300

S9303, S9306, S9312

V100R002, V100R003, V100R006(C00&C01), V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9310

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300X

S9310X

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300E

S9303E, S9306E, S9312E

V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • Table 4-6 describes the VLAN specifications of different switch models.
    Table 4-6  VLAN specifications of different switch models
    Item Specification

    Maximum number of VLANs in the system

    4096 (VLAN 0 and VLAN 4095 are reserved)

    Maximum number of VLANIF interfaces in the system

    S9303/S9303E: 2048; other models: 4094

  • Plan service and management VLANs so that any broadcast storms in service VLANs do not affect switch management.
  • In practice, specify VLANs from which packets need to be transparently transmitted by a trunk interface. Avoid using the port trunk allow-pass vlan all command if possible.
  • Before changing the interface type, restore the default VLAN of the interface.
  • Before deleting a VLAN where a VLANIF interface has been configured, run the undo interface vlanif vlan-id command to delete the VLANIF interface.
  • All interfaces join VLAN 1 by default. When unknown unicast, multicast, or broadcast packets of VLAN 1 exist on the network, broadcast storms may occur. Note the following guidelines and limitations when using VLAN 1:
    • Do not use VLAN 1 as the management VLAN or service VLAN.
    • To prevent loops, remove unnecessary interfaces from VLAN 1. Configure a trunk interface to permit packets from VLAN 1. If a trunk interface rejects packets from VLAN 1, some protocol packets transmitted in VLAN 1 may be incorrectly discarded. To prevent such faults, take measures to prevent potential risks when packets of VLAN 1 are allowed to pass through.
    • If a spanning tree protocol is used and a trunk interface on the switch rejects packets from VLAN 1, run the stp bpdu vlan command to enable the switch to encapsulate the specified VLAN ID in outgoing STP BPDUs so that the spanning tree protocol runs properly.
    • You are advised to remove interfaces from VLAN 1 in Eth-Trunk or ring networking.
    • When the switch connects to an access device, do not configure the uplink interface of the access device to transparently transmit packets from VLAN 1. This prevents broadcast storms in VLAN 1.
    • When an interface is bound to a VLANIF interface for Layer 3 forwarding, remove the interface from VLAN 1 to prevent Layer 2 loops in VLAN 1.
Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038290

Views: 101193

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next