No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X V200R012C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for RRPP

Licensing Requirements and Limitations for RRPP

Involved Network Elements

Other network elements are not required.

Licensing Requirements

RRPP is a basic feature of a switch and is not under license control.

RRPP snooping can be only used on the device enabled with MPLS. MPLS requires a license. By default, MPLS of a newly purchased device is disabled. To use MPLS, apply for and purchase the license from the equipment supplier.

Version Requirements

Table 17-4  Products and versions supporting RRPP

Product

Product Model

Software Version

S9300

S9303, S9306, S9312

V100R002, V100R003, V100R006(C00&C01), V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300

S9310

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300X

S9310X

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300E

S9303E, S9306E, S9312E

V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • SA series cards do not support RRPP snooping.
  • Switch XGE interfaces connected to the LE1D2FW00S01 and ACU2 cards do not support RRPP snooping.
  • After VLAN stacking is configured on an interface of an SA series card, the interface cannot be configured in an RRPP ring.
  • When you configure the list of protected VLANs, note the following points:

    • Protected VLANs must be configured before you configure an RRPP ring.

    • You can delete or change existing protected VLANs before configuring an RRPP ring. The protected VLANs cannot be changed after the RRPP ring is configured.

    • In the same physical topology, the control VLAN in a domain cannot be configured as a protected VLAN in another domain.

    • The control VLAN must be included in the protected VLANs; otherwise, the RRPP ring cannot be configured.

    • The control VLAN can be mapped to other instances before the RRPP ring is created. After the RRPP ring is created, the mapping cannot be changed unless you delete the RRPP ring.

    • When the mapping between instances and VLANs changes, the protected VLANs in the RRPP domain also change.

    • All the VLANs allowed by an RRPP interface must be configured as protected VLANs.

Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038290

Views: 101182

Downloads: 24

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next