No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X V200R012C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Using a QinQ Termination Sub-interface to Connect to a VPN

Using a QinQ Termination Sub-interface to Connect to a VPN

Using a QinQ Termination Sub-interface to Connect to a PWE3/VLL/VPLS Network

In Figure 8-5, different branches of an enterprise are interconnected through a carrier's PWE3/VLL/VPLS network. PEs serve as edge devices of the carrier's PWE3/VLL/VPLS network and connect to branch networks through sub-interfaces, and packets sent from CEs to PEs carry double VLAN tags. User hosts in different branches need to communicate with each other.

Figure 8-5  Using a QinQ termination sub-interface to connect to a PWE3/VLL/VPLS network
QinQ termination and PWE3/VLL/VPLS are configured on sub-interfaces of PE1 and PE2. When a host in Branch 1 sends packets to a host in Branch 2, the process is as follows:
  1. PE1 checks the inner and outer VLAN tags of data packets sent from CE1. If these VLAN tags are the same as those specified in the QinQ termination configuration on Port1.1, PE1 encapsulates the packets with double MPLS labels into the packets and forwards the packets to the carrier's PWE3/VLL/VPLS network. VLAN tags are transparent to the carrier's PWE3/VLL/VPLS network.
  2. When receiving the packets, PE2 removes the double MPLS labels from the packets, and forwards the packets to CE2 according to the QinQ termination configuration on Port1.1.
  3. CE2 forwards packets to user hosts.
The process is reversed when a host in Branch 2 sends packets to a host in Branch 1.

Using a QinQ Termination Sub-interface to Connect to an L3VPN

In Figure 8-6, different branches of an enterprise are interconnected through a carrier's MPLS L3VPN. PEs serve as edge devices of the carrier's MPLS L3VPN and connect to branch networks through sub-interfaces, and packets sent from CEs to PEs carry double VLAN tags. Hosts in different branches need to use the same services.

Figure 8-6  Using a QinQ termination sub-interface to connect to an L3VPN
QinQ termination and L3VPN are configured on sub-interfaces of PE1 and PE2. When a host in Branch 1 of VPN 1 sends packets to a host in Branch 2 of VPN 1, the process is as follows:
  1. According to the Dot1q termination configuration on Port1.1, PE1 removes the inner and outer VLAN tags of the packets sent from CE1.
  2. PE1 binds the inner and outer VLAN tags to the VPN instance VPN1, and forwards the packets to the L3VPN.
  3. After the packets reach PE2, PE2 determines that the packets are destined for CE3 based on the VPN instance.
  4. PE2 adds inner and outer VLAN tags to the packets according to the QinQ termination configuration on Port1.1, and then forwards the packets to CE3.
  5. CE3 forwards the packets to the destination user host.
The process is reversed when a host in Branch 2 of VPN 1 sends packets to Branch 1 of VPN 1.
Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038290

Views: 110669

Downloads: 24

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next