No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

S9300, S9300E, and S9300X V200R012C00 Configuration Guide - Ethernet Switching

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VLAN Mapping

Licensing Requirements and Limitations for VLAN Mapping

Involved Network Elements

Other network elements are not required.

Licensing Requirements

VLAN mapping is a basic feature of a switch and is not under license control.

Version Requirements of VLAN Mapping

Table 11-1  Products and versions supporting VLAN mapping

Product

Product Model

Software Version

S9300

S9303, S9306, S9312

V100R002, V100R003, V100R006(C00&C01), V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300

S9310

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300X

S9310X

V200R010C00, V200R011C10, V200R012C00, V200R013C00

S9300E

S9303E, S9306E, S9312E

V200R001C00, V200R002C00, V200R003C00, V200R005C00SPC300, V200R006C00, V200R007C00, V200R008(C00&C10), V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • The LE0MG24CA and LE0MG24SA cards do not support 2:1 and 2:2 VLAN mapping.
  • VLAN mapping can be configured only on a trunk or hybrid interface, and the hybrid interface must be added to the translated VLAN. The interfaces on the SA cards of S series must be added to the translated VLAN in tagged mode.
  • When N:1 VLAN mapping is configured, the interface needs to join the original VLAN in tagged mode.

  • When VLAN mapping is configured, do not configure map-vlan to the VLAN corresponding to the VLANIF interface.

  • N:1 VLAN mapping takes effect only when the packets with original VLANs are sent first.
  • LE1D2S04SEC0, LE1D2X32SEC0, and LE1D2H02QEC0 cards, X series cards and SA boards of S series cards do not support N:1 VLAN mapping.
  • N:1 VLAN mapping is not supported on an Eth-Trunk.

  • If a large number of VLAN mappings are configured in a version earlier than V100R006 and the version is upgraded to V100R006 or a later version, a message indicating insufficient resources or hash conflicts may be displayed during VLAN mapping configuration, affecting services.

Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038290

Views: 112665

Downloads: 24

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next