No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

S1720, S2700, S5700, and S6720 V200R012(C00 and C20)

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VCMP

Licensing Requirements and Limitations for VCMP

Involved Network Elements

Other network elements are not required.

Licensing Requirements

VCMP is a basic feature of a switch and is not under license control.

Version Requirements

Table 12-3  Products and versions supporting VCMP
Product Product Model

Software Version

S2700 S2700SI Not supported
S2700EI Not supported
S2710SI Not supported
S2720EI

V200R006C10, V200R009C00, V200R010C00, V200R011C10, V200R012C00

S2750EI

V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S3700 S3700SI Not supported
S3700EI Not supported
S3700HI Not supported
S5700 S5700LI/S5700S-LI

V200R005C00SPC300, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5710-C-LI Not supported
S5710-X-LI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5700EI

V200R005(C00&C01&C02&C03)

S5700SI

V200R005C00

S5710EI

V200R005(C00&C02)

S5720EI

V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5720LI/S5720S-LI

V200R010C00, V200R011C00, V200R011C10, V200R012(C00&C20)

S5720SI/S5720S-SI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5720I-SI

V200R012C00

S5700HI

V200R005(C00SPC500&C01&C02)

S5710HI

V200R005(C00&C02&C03)

S5720HI

V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S5730HI

V200R012C00

S5730SI

V200R011C10, V200R012C00

S5730S-EI

V200R011C10, V200R012C00

S6700 S6700EI

V200R005(C00&C01&C02)

S6720EI

V200R008C00, V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S6720S-EI

V200R009C00, V200R010C00, V200R011C00, V200R011C10, V200R012C00

S6720LI, S6720S-LI

V200R011C00, V200R011C10, V200R012C00

S6720SI, S6720S-SI

V200R011C00, V200R011C10, V200R012C00

S6720HI

V200R012C00

NOTE:

For details about software mappings, visit Hardware Query Tool and search for the desired product model.

For feature support of S1700 series switches, see S1700 Series Enterprise Switches - Specifications.

Feature Limitations

  • VCMP can only help the network administrator synchronize VLAN information but not dynamically assign interfaces to VLANs. VCMP is often used with LNP to simplify user configurations. For details about LNP, see "LNP" in "VLAN Configuration" in the Configuration Guide - Ethernet Switching of the corresponding product version.

  • VCMP packets can be only transmitted in VLAN 1. By default, all interfaces join VLAN 1. To prevent loops, deploy a loop prevention protocol such as STP in addition to VCMP.

  • By default, a switch is a VCMP client. After a switch is upgraded from a version earlier than V200R005C00 to V200R005C00 or a later version, the role of the switch is silent.

  • VCMP synchronizes only the VLAN ID in the current version.

  • One switch can join only one VCMP domain, and only one VCMP server exists in a VCMP domain.

  • If the VCMP domain authentication password is set, ensure that the VCMP server and clients use the same VCMP domain authentication password.

  • If VLANs created or deleted on the VCMP server are the control VLANs of the Ethernet Ring Protection Switch (ERPS), Rapid Ring Protection Protocol (RRPP), Smart Ethernet Protocol (SEP), or Smart link, or reserved VLANs of stack, a VCMP client does not create or delete the VLANs.

  • If the Generic VLAN Registration Protocol (GVRP) has been enabled, the VCMP role can be only the transparent or silent switch. If the VCMP role is set to client or server, do not use GVRP.

  • Termination sub-interfaces cannot be configured on a VCMP client. For details on how to configure a termination sub-interface, see "Configuring a Sub-interface" in "Logical Interface Configuration" in the Configuration Guide - Interface Management of the corresponding product version.

  • After a VLAN is deleted on the VCMP server, VCMP clients delete the VLAN but do not delete configurations in the VLAN. In addition, the vlan vlan-id configuration command is generated in the configuration file, and the configurations in the deleted VLAN specified by vlan-id are moved to the VLAN configuration view.
  • When the device used as a VCMP client that connects to a VCMP server restarts, the VLAN configuration before the restart takes effect. To make the saved VLAN configuration take effect, use one of the following methods to delete the vlan.dat file and then restart the device:
    • Run the vcmp role { server | silent | transparent } command to change the device role to a non-client.
    • Run the startup saved-configuration configuration-file command to configure a new configuration file. Ensure that the name of the new configuration file is different from that of the current configuration file.
    • Run the reset saved-configuration command to clear the saved configuration file. This command will clear all the configuration.
    NOTE:

    When the value of Server ID in the display vcmp status command output is not empty, the device used as a VCMP client has been connected to a VCMP server.

Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038339

Views: 158549

Downloads: 685

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next