No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Bluetooth Data Transparent Transmission

Configuring Bluetooth Data Transparent Transmission

Pre-configuration Tasks

Before configuring Bluetooth data transparent transmission, complete the following tasks:

Table 18-5  Pre-configuration tasks

Task

Description

Create an AP group

Each AP will be added and can be added to only one AP group. An AP group is typically used to provide the same configurations for multiple APs. By default, the system has an AP group default. To create an AP group, execute this task. For details, see Creating an AP Group.

Configure an AP to go online

Configure a DHCP server

To go online normally, APs and STAs must obtain IP addresses. You can configure an AC as a DHCP server or use an independent DHCP server to allocate IP addresses to APs and STAs. For details, see Configuring a DHCP Server.

Configure network interconnections

To enable APs and STAs to obtain IP addresses, APs to discover the AC and go online on the AC, and STAs to access the network, configure interconnections between network devices. For details, see Configuring Network Interconnections.

Configure country codes

Correct country code configuration ensures that radio attributes of APs comply with laws and regulations of countries and regions to which the APs are delivered. For details, see Configuring Country Codes.

Configure a source interface

Before an AP establishes a CAPWAP tunnel with an AC, a source interface or source address must be specified for the AC. For details, see Configuring a Source Interface or Source Address.

Add APs

You can add APs in any of the following modes:
  • Importing APs offline.
  • Configuring AC to automatically discover an AP.
  • Manually confirming APs added to the list of unauthorized APs.
Adding an AP offline is recommended when the MAC address or SN of the AP is already learned. For details, see Adding APs.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Run ble-profile name profile-name

    A BLE profile is created.

    By default, no BLE profile is created.

  4. Run sniffer enable transparent-mode

    Bluetooth data transparent transmission is enabled on an AP's built-in Bluetooth module.

    By default, the Bluetooth function of an AP's built-in Bluetooth module is disabled.

  5. Run report enable

    An AP is enabled to send Bluetooth data packets for transparent transmission.

    By default, an AP is disabled from sending Bluetooth packets.

  6. (Optional) Run report-mode { immediate | periodic [ interval interval ] }

    The mode of sending Bluetooth data packets for transparent transmission is configured.

    By default, an AP sends Bluetooth packets at an interval of 10 seconds.

  7. Run report-to-server ip-address ip-address port port-num [ via-ac ac-port ac-port-num ] or report-to-server domain domain port port-num

    The destination IP address and port number are configured for an AP to send Bluetooth data packets for transparent transmission.

    By default, no destination IP address or port number is configured for APs to report Bluetooth packets.

  8. Run quit

    Return to the WLAN view.

  9. The AP view or AP group view is displayed.

    • Run the ap-group name group-name command to enter the AP group view.
    • Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.

  10. Run ble-profile profile-name

    A BLE profile is bound to the AP or AP group.

    By default, no BLE profile is bound to an AP group or AP.

  11. Run quit

    Return to the WLAN view.

  12. (Optional) Run ble report interval interval-value

    The interval at which an AP reports Bluetooth device information is set.

    By default, an AP reports Bluetooth device information at an interval of 10 minutes.

  13. (Optional) Run ble monitoring-list mac mac-address1 [ to mac-address2 ]

    Specified Bluetooth clients are added to the monitoring list of an AP's built-in Bluetooth module.

    By default, no Bluetooth devices are added to the monitoring list.

    When no Bluetooth device is added to the monitoring list, all Bluetooth devices are monitored. When any Bluetooth device is offline or has insufficient battery power, an alarm is triggered on the AC accordingly. When Bluetooth devices are added to the monitoring list, only the Bluetooth devices in the list are monitored. When a Bluetooth device in the monitoring list is offline or has insufficient battery power, an alarm is triggered on the AC accordingly. Bluetooth clients do not support low power alarms.

Verifying the Configuration

  • Run the display ble-profile { all | name profile-name } command to check configuration and reference information about a BLE profile.

  • Run the display wlan ble global configuration command to check global configurations of Bluetooth devices.

  • Run the display references ble-profile name profile-name command to check reference information about a BLE profile.

Follow-up Procedure

After Bluetooth data transparent transmission is configured, servers need to collect data from Bluetooth clients for effective Bluetooth data analysis.

Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 111166

Downloads: 368

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next