No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring APs to Report KPIs

Configuring APs to Report KPIs

Context

Only WMI-supported APs can report KPIs to a WMI server.

Currently, only cloud devices can report STA location data, log data, and security data to the WMI server.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Run wmi-server name profile-name

    A WMI profile is created and the WMI profile view is displayed.

    By default, no WMI profile is created.

  4. Run server ip-address ip-address port port

    The destination IP address and port number are configured for APs to report KPI information.

    By default, no destination IP address or port number is configured for APs to report KPI information.

  5. (Optional) Run keepalive { interval interval | retry-interval retry-interval | retry-number retry-number } *

    Connection parameters between APs and the WMI server are set.

    By default, the heartbeat interval is 3 minutes, the reconnection interval is 5 minutes, and the number of reconnection attempts is 0.

    The value 0 indicates that the server and APs always attempt to reconnect to each other.

  6. (Optional) Run max-packet-size size

    The maximum data length of KPI information sent by APs to a WMI server is specified.

    By default, the maximum data length of KPI information sent by APs to a WMI server is 5 KB.

  7. (Optional) Run report-interval interval

    The interval for APs to report KPI information to a WMI server is specified.

    By default, APs report KPI information to a WMI server at an interval of 60 seconds.

  8. (Optional) Run collect-item { device-data | interface-data | location-data | log-data | radio-data | security-data | ssid-data | terminal-data } { interval interval | disable }

    Whether APs report collected data to a WMI server is configured, and the data collection interval is specified.

    By default, APs report all types of collected data to a WMI server. The data collection interval varies depending on the data type, as listed in Table 32-3.
    Table 32-3  Default settings of the data collection interval
    Data Type

    Default Data Collection Interval (Unit: Second)

    Device monitoring data 10
    Interface monitoring data 60
    STA location data 60
    Log data 300
    Radio monitoring data 10
    Security data 60
    SSID monitoring data 60
    STA data 10

    You can run this command multiple times to configure APs to report different types of data to the WMI server.

  9. Run quit

    Return to the WLAN view.

  10. Run ap-system-profile name profile-name

    An AP system profile is created, and the AP system profile view is displayed.

    By default, the system provides the AP system profile default.

  11. Run wmi-server profile-name

    The WMI profile is bound to the AP system view.

    By default, no WMI profile is bound to an AP system profile.

  12. Run quit

    Return to the WLAN view.

  13. Bind an AP system profile to an AP group or AP.

    • Binding an AP system profile to an AP group.
      1. Run the ap-group name group-name command to enter the AP group view.
      2. Run the ap-system-profile profile-name command to bind the AP system profile to the AP group.

        By default, the AP system profile default is bound to an AP group.

    • Binding an AP system profile to an AP.
      1. Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.
      2. Run the ap-system-profile profile-name command to bind the AP system profile to the AP.

        By default, no AP system profile is bound to an AP.

Verifying the Configuration

  • Run the display wmi-server { all | name wmi-server-name } command to check configuration and reference information about a WMI profile.
  • Run the display references wmi-server name wmi-server-name command to check reference information about a WMI profile.
Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 158801

Downloads: 436

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next