No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Parameters for an AP's Wired Interface

Configuring Parameters for an AP's Wired Interface

Context

You can configure the wired interface on a root AP to connect to the AC or configure the wired interface on an AP to deploy a Layer 2 network or directly associate with STAs.

On WDS networks, an AP wired interface can work in the following modes:

  • root mode: The wired interface that connects the root AP to the AC must work in root mode.
  • endpoint mode: When the wired interface of an AP works in endpoint mode, the AP's wired interface can directly connect to a STA or be used to deploy Layer 2 networks.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Run wired-port-profile name profile-name

    An AP wired port profile is created and the AP wired port profile view is displayed.

    By default, the system provides the AP wired port profile default.

  4. Set parameters for an AP wired interface.

    • Configure a wired interface to work in root mode.
      1. Run the mode root command to configure an AP's wired interface to work in root mode.

        By default,
        • On a common AP: Its GE interfaces work in root mode, Ethernet interfaces in endpoint mode, and Eth-Trunk interfaces in root mode.
        • On a central AP: Its uplink GE interfaces in root mode and downlink GE interfaces work in middle mode.
        • On an R230D: Its Ethernet interface works in root mode.
        • On an R240D: Its Ethernet interface works in endpoint mode and GE interface in root mode.
        • On an R250D, R250D-E, AP2050DN, AP2051DN, AP2051DN-E, R251D, R251D-E and AP2050DN-E: Their uplink GE interfaces work in root mode and downlink GE interfaces in endpoint mode.
        • On an R450D: Its GE interface works in root mode.
    • Configure a wired interface to work in endpoint mode.
      1. Run the mode endpoint command to configure an AP's wired interface to work in endpoint mode.

        By default,
        • On a common AP: Its GE interfaces work in root mode, Ethernet interfaces in endpoint mode, and Eth-Trunk interfaces in root mode.
        • On a central AP: Its uplink GE interfaces in root mode and downlink GE interfaces work in middle mode.
        • On an R230D: Its Ethernet interface works in root mode.
        • On an R240D: Its Ethernet interface works in endpoint mode and GE interface in root mode.
        • On an R250D, R250D-E, AP2050DN, AP2051DN, AP2051DN-E, R251D, R251D-E and AP2050DN-E: Their uplink GE interfaces work in root mode and downlink GE interfaces in endpoint mode.
        • On an R450D: Its GE interface works in root mode.
      2. Run the vlan pvid vlan-id command to configure the PVID of an AP's wired interface.

        By default, no PVID is configured for an AP wired interface.

      3. Run the vlan { tagged | untagged } { vlan-id1 [ to vlan-id2 ] } &<1-10> command to add an AP's wired interface to VLANs.

        By default, an AP wired interface allows packets from all VLANs to pass. The wired interface is added to VLAN 1 in untagged mode and to other VLANs in tagged mode.

        NOTE:

        An AP wired interface can be added to a maximum of 256 VLANs.

      4. Run the user-isolate { all | l2 } command to enable user isolation on an AP's wired interface.

        By default, user isolation is disabled on an AP's wired interface.

Follow-up Procedure

Run the wired-port-profile profile-name interface-type interface-number command in the AP group view or AP view to bind the specified AP wired port profile to the AP's wired interface.

Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 109383

Downloads: 368

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next