No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring Customer Flow Analysis

Configuring Customer Flow Analysis

Context

Customer flow analysis allows APs to obtain information about STAs (such as the MAC address, time stamp, and RSSI) in a shopping mall through the Wi-Fi terminal location function. The APs then send the information to the customer flow analysis server for statistics collection and analysis.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Set the working mode for radios in an AP group or for a specified radio.

    You can set the radio working mode in the AP radio view or AP group radio view. The configuration in the AP group radio view takes effect on all AP radios in an AP group and that in the AP radio view takes effect only on a specified AP radio. The configuration in the AP radio view has a higher priority than that in the AP group radio view.

    • Set the working mode for all radios in an AP group.
      1. Run the ap-group name group-name command to enter the AP group view.
      2. Run the radio radio-id command to enter the radio view.
      3. Run the work-mode { normal | monitor [ dual-band-scan enable ] } command to set the working mode for radios in an AP group.

        By default, radios in an AP group work in normal mode.

      4. Run the quit command to return to the AP group view.

    • Set the working mode for a specified AP radio.
      1. Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.
      2. Run the radio radio-id command to enter the radio view.
      3. Run the work-mode { normal | monitor [ dual-band-scan enable ] } command to set the working mode for a specified AP radio.

        By default, an AP radio works in normal mode.

      4. Run the quit command to return to the AP view.

    NOTE:
    An AP can work in two modes:
    • normal: indicates the normal mode.
      • If the air scan function is disabled on a radio, including WIDS, spectrum analysis, and terminal location, the radio is used to transmit common WLAN services.
      • If the air scan function is enabled on a radio, the radio transmits common WLAN services and also implements detection. Transmission of common WLAN services may be affected.
    • monitor: indicates the monitor mode.

      In this mode, the radio can only transmit WLAN services scanned by the air interface but cannot transmit common WLAN services.

  4. Run quit

    Return to the WLAN view.

  5. Run air-scan-profile name profile-name

    An air scan profile is created and the air scan profile view is displayed.

    By default, the system provides the air scan profile default.

  6. Run the undo scan-disable command to enable the air scan function.

    By default, the air scan function is enabled.

  7. Run scan-channel-set { country-channel | dca-channel | work-channel }

    An air scan channel set is configured.

    By default, an air scan channel set contains all channels supported by the country code of an AP.

  8. (Optional) Run scan-period scan-time

    The period during which the AP scans channels is configured.

    The default period during which an AP scans channels is 60 ms.

    The channel scan period applies to radio calibration, smart roaming, WLAN location, and WIDS functions.

    A shorter channel scan period means fewer location packets that the device can obtain, which affects the location accuracy. A longer channel scan period has a much larger impact on services.

  9. (Optional) Run scan-interval scan-time

    The interval at which the AP scans channels is configured.

    By default, the air scan interval is 10000 ms.

    The channel scan interval applies to radio calibration, smart roaming, WLAN location, and WIDS functions.

    NOTE:
    • If the customer has high requirements on real-time data analysis, configure a small air scan interval using the scan-interval command to improve the scan frequency; however, higher scan frequency indicates much larger impact on the services.

    • If the customer has high requirements on real-time locating services, deploy the APs on the same channel to scan channels.

  10. Run quit

    Return to the WLAN view.

  11. Run radio-2g-profile name profile-name or radio-5g-profile name profile-name

    The radio profile view of the specified AP is displayed.

    • By default, the system provides the 2G radio profile default.
    • By default, the system provides the 5G radio profile default.

  12. Run air-scan-profile profile-name

    The air scan profile is bound to the radio profile.

    By default, the air scan profile default is bound to a radio profile.

  13. Run quit

    Return to the WLAN view.

  14. (Optional) Configure the WIDS function according to Configuring Device Detection and Containment and Configuring Attack Detection and a Dynamic Blacklist.

    To use the Wi-Fi terminal location function to locate unauthorized STAs, rogue APs and bridges, and ad-hoc devices, you need to enable WIDS. To use the Wi-Fi terminal location function to locate authorized STAs, you do not need to enable WIDS.

  15. Run vap-profile name profile-name

    A VAP profile is created.

    By default, the system provides the VAP profile default.

    NOTE:

    When a VAP profile exists in the system, you can use the existing one or create a new one.

  16. Run quit

    Return to the WLAN view.

  17. Bind the VAP profile to radios of an AP group or a specific AP as required to make the radios properly work. For details, see Binding VAP Profiles.
  18. Run quit

    Return to the WLAN view.

  19. Run location-profile name profile-name

    A location profile is created and the location profile view is displayed.

    By default, no location profile is created.

  20. Run private mu-enable

    Wi-Fi terminal location is enabled on the AP.

    Locating a STA requires at least three APs to scan signals on the WLAN.

    By default, Wi-Fi terminal location is disabled on an AP.

  21. (Optional) Run private report-frequency time

    The interval at which the AP reports channel scan information is configured.

    By default, an AP reports channel scan information every 20s (20000 ms).

  22. (Optional) Run private report-protocol { udp | http | https ssl-policy ssl-policy }

    The protocol type used by APs to report information is configured.

    By default, an AP uses UDP to reports information.

  23. (Optional) Run private mu protocol-version { v3 | v5 }

    The STA location protocol version is configured.

    The default terminal location protocol version is v3.

  24. Run private server { ip-address ip-address | domain domain } port port-num [ via-ac ac-port ac-port-num ]

    The destination IP address and port number are configured for the AP to report STA location data.

    By default, no destination IP address or port number is configured for the AP to report STA location data.

  25. Run quit

    Return to the WLAN view.

  26. Enter the AP group view or AP view.

    • Run the ap-group name group-name command to enter the AP group view.
    • Run the ap-id ap-id, ap-mac ap-mac, or ap-name ap-name command to enter the AP view.

  27. Run radio-2g-profile profile-name { radio { radio-id | all } } or radio-5g-profile profile-name { radio { radio-id | all } }

    The radio profile is bound to the AP group or AP.

    • By default, the 2G radio profile default is bound to an AP group, but no 2G radio profile is bound to an AP.
    • By default, the 5G radio profile default is bound to an AP group, but no 5G radio profile is bound to an AP.

  28. Run location-profile profile-name radio { radio-id | all }

    The location profile is bound to the specified radio on the AP.

    By default, no location profile is bound to a radio.

Verifying the Configuration

  • Run the display location-profile name profile-name command to check Wi-Fi terminal location configurations.

Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 111606

Downloads: 368

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next