No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring the AMC Algorithm for a Radio

Configuring the AMC Algorithm for a Radio


Adaptive Modulation and Coding (AMC) Algorithm for a Radio

Radios need to adjust the AMC algorithm according to different scenarios to deliver the optimal user experience. Three AMC algorithms are available:
  • auto-balance: applicable to most wireless scenarios
  • high-stability: applicable to scenarios with continuous interference.
  • high-throughput: applicable to scenarios with good wireless signals and non-continuous interference.

AMC Optimization in High-Density Scenarios

In typical high-density scenarios, a large number of hidden nodes exist, which interfere in communication between APs and STAs and affect product performance. The AMC optimization function can reduce such interference and improve the AMC algorithm performance.
  • It is recommended that this function be enabled in high-density scenarios where directional antennas are used.
  • This function is not applicable to scenarios where STAs move fast between APs.

Pre-configuration Tasks

Before configuring the adaptive modulation and coding (AMC) algorithm, perform the task of WLAN Service Configuration.


  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Run rrm-profile name profile-name

    An RRM profile is created, and the RRM profile view is displayed.

  4. Run amc-policy { auto-balance | high-stability | high-throughput }

    An AMC algorithm is configured for the radio.

    By default, a radio uses the AMC algorithm auto-balance.
    This takes effect only on APs in compliance with 802.11n.

  5. Run high-density amc-optimize enable

    The AMC optimization function in high-density scenarios is enabled.

    By default, the AMC optimization function is disabled in high-density scenarios.

    • This takes effect only on APs in compliance with 802.11ac Wave 2.
    • This function does not take effect in MU-MIMO mode.

  6. Run quit

    Return to the WLAN view.

  7. Bind the RRM profile to a radio profile.
    1. Run the radio-2g-profile name profile-name or radio-5g-profile name profile-name command to enter the 2G or 5G radio profile view.
    2. Run the rrm-profile profile-name command to bind the RRM profile to the 2G or 5G radio profile.
    3. Run the quit command to return to the WLAN view.
  8. Bind the radio profile to an AP group or a specific AP. For the detailed procedure, see Binding a Radio Profile.

Verifying the Configuration

  • Run the display rrm-profile name profile-name command to check the AMC algorithm configured for radios in the RRM profile.
  • Run the display radio-2g-profile name profile-name command to check the RRM profile bound to the 2G radio profile.
  • Run the display radio-5g-profile name profile-name command to check the RRM profile bound to the 5G radio profile.
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 200065

Downloads: 507

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next