No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - WLAN-AC

S5700 and S6720 V200R012C00

This document describes the configurations of WLAN, including WLAN Service Configuration, Radio Resource Management, Roaming, WLAN QoS, WLAN Security, WDS, Mesh, Location, Hotspot 2.0, Dual-Link Cold Backup, N+1 Backup.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring ANQP Parameters

Configuring ANQP Parameters

Context

If a Hotspot 2.0 network parameter carries multiple data entries, you need to configure the parameter using a profile. In the profile, you can configure the entries of the parameter and then bind the profile to a Hotspot 2.0 profile.

Table 19-4 describes the configurable parameter profiles. Not all parameter profiles are mandatory. You can configure profiles according to network settings to provide required network information for STAs.

Table 19-4  Description of the parameter profiles

Parameter Profile

Description

Cellular network profile

Recommended

You can configure Hotspot 2.0 services on cellular networks. When connecting to the networks, user terminals can obtain network information from APs, which helps them to select desired networks.

NAI realm profile

Recommended

A NAI realm profile is used to configure the network access identifier (NAI) realm name, authentication mode, and authentication parameters for networks accessible to users.

Roaming consortium profile

Recommended

If the user terminals need to roam among Hotspot2.0 networks of different operators, configure a roaming consortium profile and add the organization identifiers (OIs) of the operators to the roaming consortium profile. In this way, after the user terminals connect to a network of an operator in the profile, they can roam to networks of the other operators while maintaining online.

Connection capability profile

Optional

You can configure Hotspot2.0 services for networks. When user terminals connect to the networks, they can obtain network connection capability information from APs, including allowed protocols and ports, which helps them to select desired networks.

Operating class profile

Optional

The operating class profile is used to configure the operating class indication of AP in on the hotspot2.0 network. When a STA accesses the network, it can obtain channel information used to access a Wi-Fi frequency from AP so that the STA can set up a connection.

Operator domain profile

Recommended

A network domain name profile is used to configure the operator domain profile. STAs can obtain the domain name information through ANQP, which is used as a basis for network selection.

Operator name profile

Optional

You can specify different friendly names for different languages so that users can select networks.

Venue name profile

Optional

When configuring Hotspot2.0 services, configure network parameters according to operator requirements. When connecting to networks, user terminals can obtain the network parameters to select desired networks. The venue name describes physical locations of a network and is an optional parameter.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run wlan

    The WLAN view is displayed.

  3. Configure parameter profiles.

    • Cellular network profile

      1. Run the cellular-network-profile name profile-name command to create a cellular network profile and enter the cellular network profile view.

        By default, no cellular network profile exists in the system.

      2. Run the plmn-id plmn-id command to set the PLMN ID.

        By default, no PLMN identifier is configured in the cellular network profile.

      3. Run the quit command to return to the WLAN view.

    • NAI realm profile

      1. Run the nai-realm-profile name profile-name command to create an NAI realm profile and enter the NAI realm profile view.

        By default, no NAI realm profile is available in the system.

      2. Run the nai-realm realm-name realm-name [ eap-method-type eap-method-type [ eap-authen-id eap-authen-id eap-authen-para eap-authen-para ] ] command to configure an NAI realm.

        By default, no NAI realm is configured.

      3. Run the quit command to return to the WLAN view.

    • Roaming consortium profile

      1. Run the roaming-consortium-profile name profile-name command to create a roaming consortium profile and enter the roaming consortium profile view.

        By default, no roaming consortium profile is created.

      2. Run the roaming-consortium-oi oi-value [ in-beacon ] command to set the roaming-consortium organization identifier (OI).

        By default, no roaming consortium identifier is configured for the Hotspot2.0 network.

      3. Run the quit command to return to the WLAN view.

    • Connection capability profile

      1. Run the connection-capability-profile name profile-name command to create a connection capability profile and enter the connection capability profile view.

        By default, no connection capability profile exists in the system.

      2. Run the connection-capability { esp | icmp | tcp-ftp | tcp-http | tcp-pptp-vpn | tcp-ssh | tcp-tls-vpn | tcp-voip | udp-ike2-4500 | udp-ike2-500 | udp-voip } { on | off } command to set whether Hotspot 2.0 networks support common IP protocols and ports.

        By default, no supported protocol is specified in a connection capability profile.

      3. Run the quit command to return to the WLAN view.

    • Operating class profile

      1. Run the operating-class-profile name profile-name command to create an operating class profile and enter the operating class profile view.

        By default, no operating class profile is configured in the system.

      2. Run the operating-class-indication operating-class-value command to configure the operating class identifier used by the AP.

        By default, no operating class indication is configured in the system.

      3. Run the quit command to return to the WLAN view.

    • Operator domain profile

      1. Run the operator-domain-profile name profile-name command to create an operator domain profile and enter the operator domain profile view.

        By default, no network domain name profile is available in the system.

      2. Run the domain-name domain-name command to configure a domain name for a hotspot operator.

        By default, no domain name is configured for a hotspot operator.

      3. Run the quit command to return to the WLAN view.

    • Operator name profile

      1. Run the operator-name-profile name profile-name command to create an operator name profile and enter the operator name profile view.

        By default, no network domain name profile is available in the system.

      2. Run the operator-friendly-name language-code language-code name name command to configure a friendly operator name.

        By default, no operator friendly name is configured in an operator name profile view.

      3. Run the quit command to return to the WLAN view.

    • Venue name profile

      1. Run the venue-name-profile name profile-name command to create a venue name profile and enter the venue name profile view.

        By default, no venue name profile is created.

      2. Run the venue-name language-code language-code name venue-name command to configure the venue name.

        By default, no venue name is configured.

      3. Run the quit command to return to the WLAN view.

  4. Run the hotspot2-profile name profile-name command to enter the Hotspot 2.0 profile view.
  5. Bind the parameter profiles to the Hotspot 2.0 profile.

    • Run the cellular-network-profile profile-name command to bind the cellular network profile to the Hotspot 2.0 profile.
    • Run the nai-realm-profile profile-name command to bind the NAI realm profile to the Hotspot 2.0 profile.
    • Run the roaming-consortium-profile profile-name command to bind the roaming consortium profile to the Hotspot 2.0 profile.
    • Run the connection-capability-profile profile-name command to bind the connection capability profile to the Hotspot 2.0 profile.
    • Run the operating-class-profile profile-name command to bind the operating class profile to the Hotspot 2.0 profile.
    • Run the operator-domain-profile profile-name command to bind the operator domain profile to the Hotspot 2.0 profile.
    • Run the operator-name-profile profile-name command to bind the operator name profile to the Hotspot 2.0 profile.
    • Run the venue-name-profile profile-name command to bind the venue name profile to the Hotspot 2.0 profile.

Translation
Download
Updated: 2018-12-24

Document ID: EDOC1100038361

Views: 160594

Downloads: 445

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next