No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

S7700 and S9700 V200R012C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Licensing Requirements and Limitations for VLAN Switch

Licensing Requirements and Limitations for VLAN Switch

Involved Network Elements

Other network elements are not required.

Licensing Requirements

The VLAN Switch function is a basic feature of a switch and is not under license control.

Version Requirements

Table 6-3  Products and versions supporting the VLAN Switch function

Product

Product Model

Software Version

S7700

S7703, S7706, S7712

V100R003C01, V100R006C00, V200R001(C00&C01), V200R002C00, V200R003C00, V200R005C00, V200R006C00, V200R007C00, V200R008C00, V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

S7703 PoE

V200R013C00

S7706 PoE

V200R013C00

S9700

S9703, S9706, S9712

V200R001(C00&C01), V200R002C00, V200R003C00, V200R005C00, V200R006C00, V200R007(C00&C10), V200R008C00, V200R009C00, V200R010C00, V200R011C10, V200R012C00, V200R013C00

NOTE:
For details about software mappings, visit Hardware Query Tool and search for the desired product model.

Feature Limitations

  • The source and destination interfaces specified in the vlan-switch command must be hybrid or trunk interfaces, and cannot be access interfaces or Eth-Trunk member interfaces.
  • The VLANs used in the VLAN Switch function cannot be created in the system view.
  • When double-tagged VLAN Switch is configured, both inbound and outbound interfaces must be located on the X series cards or non-X series cards.
  • The switch still forwards the packets matching VLAN Switch entries when VLAN Switch is configured on the interface of a card (excluding the X series cards) and packets are discarded, including but not limited to the following situations:
    • The STP status of the interface is Blocking.
    • The action is set to discard when the interface does not learn MAC address entries.
    • The MAC address of packets is all 0s.
    • The packets contain the blackhole MAC address.
    To prevent the preceding problem, configure a traffic policy containing redirection to replace VLAN Switch.
  • The VLANs used in QinQ cannot be used by the VLAN Switch function.
  • When an outer VLAN tag in double-tagged frames is used for VLAN stacking, VLAN mapping, or control VLAN, the VLAN tag cannot be used by the VLAN Switch function.
  • On a ring network, packets matching VLAN Switch entries can pass through the interfaces blocked by loop prevention protocols. Consequently, broadcast storms may occur. Therefore, the VLAN Switch function is not recommended for a ring network.
  • SA cards of S series do not support stack-vlan.
Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038843

Views: 95164

Downloads: 67

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next