No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

S7700 and S9700 V200R012C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback :
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Enabling VBST

Enabling VBST

Context

The VBST configuration takes effect only when VBST is enabled.

When VBST is enabled on a ring network, VBST immediately starts spanning tree calculation. Parameters such as the switch priority and port priority affect spanning tree calculation, and change of these parameters may cause network flapping. To ensure fast and stable spanning tree calculation, perform basic configurations on the switch and interfaces before enabling VBST.

The PV number is the total number of VLANs into which all VBST-enabled interfaces are added. The VLANs have been established and VBST has been enabled in the VLANs. For example, VBST is enabled on 10 interfaces. Each interface is added into 100 VLANs (all VLANs have been established and VBST is enabled in the VLANs). The number of PVs occupied by all interfaces on the switch is 1000. If the number of occupied PVs exceeds the specifications, the CPU usage may be high. As a result, the switch cannot process tasks in a timely manner, protocol calculation is affected, and the switch cannot be managed by the NMS.

  • The CPU usage of VBST is in direct proportion to the number of occupied PVs.

  • You can run the display vbst port-vlan statistics command in any view to check the supported maximum number of PVs of VBST.

  • The maximum PV number supported by a switch is the sum of PV quantities supported by cards that are currently installed.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run stp mode vbst

    The working mode of the switch is set to VBST.

    By default, the switch works in MSTP mode.

    NOTE:
    • The VBST mode cannot be used with the STP/RSTP/MSTP mode.

    • When HVRP is enabled on the switch, do not change the STP mode to VBST.

    • If a protected instance in a segment has been configured by the protected-instance (sep segment view) command or a protected instance in an ERPS ring has been configured by the protected-instance (ERPS ring view) command, you must perform the operation of (Optional) Manually Configuring the Mapping between MSTIs and VLANs. Otherwise, the STP working mode cannot be changed to VBST.

    • If 1:N (N>1) mapping between MSTIs and VLANs has been configured on the switch, the mapping must be deleted before changing the STP working mode to VBST.
    • If stp vpls-subinterface enable has been configured on the switch, the undo stp vpls-subinterface enable command must be run on the interface before changing the STP working mode to VBST.

  3. Run stp enable

    Global STP is enabled.

    By default, STP is enabled globally.

  4. Run stp vlan { vlan-id1 [ to vlan-id2 ] } &<1-10> enable

    VBST is enabled in the specified VLANs.

    By default, VBST is enabled in each VLAN.

    NOTE:

    VBST cannot be enabled in the ignored VLAN or control VLAN used by ERPS, RRPP, SEP, or Smart Link.

    If VLAN mapping or VLAN stacking is configured on an interface corresponding to the VLAN, VBST negotiation for this VLAN will fail.

  5. Run interface interface-type interface-number

    The interface view is displayed.

  6. Run stp enable

    STP is enabled on the interface.

    By default, STP is enabled on each switch interface.

    NOTE:

    STP cannot be used with SEP or Smart Link. An STP-enabled interface cannot join a SEP segment or Smart Link group. Similarly, the interface that has joined the SEP segment or Smart Link group cannot be enabled with STP.

Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038843

Views: 94104

Downloads: 67

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next