No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Configuration Guide - Ethernet Switching

S7700 and S9700 V200R012C00

This document describes the configuration of Ethernet services, including configuring MAC address table, link aggregation, VLANs, VLAN aggregation, MUX VLAN, VLAN termination, Voice VLAN, VLAN mapping, QinQ, GVRP, VCMP, STP/RSTP/MSTP, VBST, SEP, RRPP, ERPS, LBDT, HVRP, and Layer 2 protocol transparent transmission.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adding a Layer 2 Interface to a SEP Segment and Configuring a Role for the Interface

Adding a Layer 2 Interface to a SEP Segment and Configuring a Role for the Interface

Context

To ensure that SEP packets are forwarded correctly in a SEP segment, add Layer 2 interfaces to the SEP segment and configure different roles for the interfaces.

After an interface is added to a SEP segment, the interface sets its interface role to the primary edge interface if the interface has the right to participate in primary edge interface election. Then, the interface periodically sends a primary edge interface election packet without waiting for the success of neighbor negotiations.

A primary edge interface election packet contains the interface role (primary edge interface, secondary edge interface, or common interface), bridge MAC address of the interface, interface ID, and integrity of the topology database.

Table 17-11 lists interface roles.
Table 17-11  Interface roles

Interface Role

Sub-role

Description

Deployment Scenario

Common interface

-

In a SEP segment, all interfaces except edge interfaces and blocked interfaces are common interfaces.

A common interface monitors the status of a directly-connected SEP link. When the link status changes, the interface sends a topology change notification message to notify its neighbors. Then the topology change notification message is flooded on the link until it finally reaches the primary edge interface. The primary edge interface determines how to process the link change.

-

Edge interface

Primary edge interface

A SEP segment has only one primary edge interface, which is determined by the configuration and election.

The primary edge interface initiates blocked interface preemption, terminates packets, and sends topology change notification messages to other networks.

Open ring networking

Closed ring networking

Multi-ring networking

Hybrid SEP+RRPP ring networking

Secondary edge interface

A SEP segment has only one secondary edge interface, which is determined by the configuration and election.

The secondary edge interface terminates packets and sends topology change notification messages to other networks.

No-neighbor primary edge interface

An interface at the edge of a SEP segment is a no-neighbor edge interface, which is determined by the configuration and election.

The no-neighbor primary edge interface terminates packets and sends topology change notification messages to other networks.

No-neighbor primary edge interfaces are used to interconnect Huawei devices and non-Huawei devices or interconnect Huawei devices and devices that do not support SEP.

Hybrid SEP+MSTP ring networking

No-neighbor secondary edge interface

The no-neighbor secondary edge interface terminates packets and sends topology change notification messages to other networks.

No-neighbor secondary edge interfaces are used to interconnect Huawei devices and non-Huawei devices or interconnect Huawei devices and devices that do not support SEP.

NOTE:
  • It is not recommended to configure primary edge interfaces and no-neighbor edge interfaces in the same SEP segment. It is not recommended to configure secondary edge interfaces and no-neighbor edge interfaces in the same SEP segment.

  • Before adding a Layer 2 interface to a SEP segment, ensure that STP has been disabled on the interface (except that the interface is a no-neighbor edge interface).

  • Before adding an interface to a SEP segment, disable Smart Link on the interface.
  • Before adding an interface to a SEP segment, disable port security on the interface; otherwise, loops cannot be prevented.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run interface interface-type interface-number

    The view of an Ethernet interface added to the SEP segment is displayed.

  3. Run port link-type { trunk | hybrid }

    The link type of the interface is set to trunk or hybrid.

  4. Run stp disable

    STP is disabled on the interface.

  5. Run sep segment segment-id [ edge [ no-neighbor ] { primary | secondary } ]

    The Ethernet interface is added to a specified SEP segment and a role is configured for the interface.

    NOTE:

    An interface can be added to a maximum of two SEP segments.

Translation
Download
Updated: 2019-01-18

Document ID: EDOC1100038843

Views: 107567

Downloads: 71

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next