No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Log Reference

CloudEngine 8800, 7800, 6800, and 5800 V200R005C00

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
VRRP/4/vrrpTrapNonMaster

VRRP/4/vrrpTrapNonMaster

Message

VRRP/4/vrrpTrapNonMaster: The VRRP status changed between backup and initialize. (ifIndex=[ifIndex], VrId=[VrId], MasterIpAddr=[MasterIpAddr], sysName=[sysName], ifName=[ifName], CurrentState=[CurrentState], ChangeReason=[ChangeReason])

Description

The VRRP status changed between Backup and Initialize.

Parameters

Parameter Name Parameter Meaning
ifIndex

Index of the interface where VRRP is configured.

VrId

VRID of the VRRP group.

MasterIpAddr

IP address of the master device in the VRRP group.

sysName

System name.

ifName

Name of the interface where VRRP is configured.

CurrentState

VRRP status after the change:

  • Initialize

  • Backup

ChangeReason

VRRP status change reason.

Possible Causes

Possible causes for the VRRP status change from Backup to Initialize are as follows:

  • Cause 1: The device on which the VRRP group is configured failed.

  • Cause 2: The interface on which the VRRP group is configured or its connected link failed.

  • Cause 3: An error occurs in association between VRRP and BFD.

Possible causes for the VRRP status change from Initialize to Backup are as follows:

  • Cause 1: The device on which the VRRP group is configured recovered.

  • Cause 2: The interface on which the VRRP group is configured or its connected link recovered.

  • Cause 3: Association between VRRP and BFD is normal.

Procedure

  1. Check whether the value of CurentState is Initialize or Backup.

    • If the value of CurentState is Initialize, go to step 2.
    • If the value of CurentState is Backup, go to step 6.

  2. Check whether the interface on which the VRRP group is configured or the link monitored by BFD that is associated with VRRP is Up.

    • If the interface on which the VRRP group is configured is Up, go to step 3.
    • If the link monitored by BFD that is associated with VRRP is Up, go to step 4.

  3. Run the display this interface command in the view of the interface on which the VRRP group is configured to check the physical and protocol statuses of the interface.

    • If the physical status of the interface is Down, the link connected to the interface fails. Rectify the fault and check whether the VRRP group has recovered.
      • If the VRRP group has recovered, go to step 6.
      • If the VRRP group has not recovered, go to step 5.
    • If the physical status of the interface is Up but its protocol status is Down, the IP address of the interface has been deleted. Reassign an IP address to the interface and check whether the VRRP group has recovered.
      • If the VRRP group has recovered, go to step 6.
      • If the VRRP group has not recovered, go to step 5.
    • If the physical and protocol statuses of the interface are both Up, the IP address of the interface is not on the same network segment as the virtual IP address of the VRRP group. Reassign an IP address to the interface and ensure that the IP address is on the same network segment as the virtual IP address of the VRRP group. Then check whether the VRRP group has recovered.
      • If the VRRP group has recovered, go to step 6.
      • If the VRRP group has not recovered, go to step 5.

  4. Run the display vrrp command and check whether the value of BFD-Session State in the command output is UP.

    • If the value of BFD-Session State in the command output is DOWN, the original standby link fails. Rectify the fault and check whether the VRRP group has recovered.
      • If the VRRP group has recovered, go to step 6.
      • If the VRRP group has not recovered, go to step 5.
    • If the value of BFD-Session State in the command output is UP, go to step 5.

  5. Collect trap, log, and configuration information, and contact technical support personnel.
  6. End.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100039602

Views: 121688

Downloads: 90

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next