No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Log Reference

CloudEngine 8800, 7800, 6800, and 5800 V200R005C00

This document provides the explanations, causes, and recommended actions of logs on the product.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
VRRP6/4/vrrp6MasterDown

VRRP6/4/vrrp6MasterDown

Message

VRRP6/4/vrrp6MasterDown: The VRRP status changed from master to another state. (ifIndex=[ifIndex], VrId=[VrId], MasterIpAddr=[MasterIpAddr], sysName=[sysName], ifName=[ifName], CurrentState=[CurrentState], ChangeReason=[ChangeReason])

Description

VRRP6 was changed from master to another state.

Parameters

Parameter Name Parameter Meaning
ifIndex

Index of the interface on which VRRP6 is configured

VrId

VRID of the VRRP6 backup group

MasterIpAddr

IP address of the master device in the VRRP6 backup group

sysName

System name

ifName

Name of the interface on which VRRP6 is configured

CurrentState

Current VRRP6 status

ChangeReason

VRRP6 status change reason

Possible Causes

Possible causes are as follows:
  • The master device in the VRRP6 backup group went down.

  • The primary link of the VRRP6 backup group went down.

  • The VRRP6 priority of the master or backup device changed.

  • VRRP6 backup group was deleted.

Procedure

  1. Check the value of CurentState to see the changed VRRP6 status.

    • If the VRRP6 status is initialize, go to Step 2.
    • If the VRRP6 status is backup, go to Step 3.

  2. Check whether the interface on which VRRP6 is configured is working properly.

    • If the interface is working properly, go to Step 5.
    • If the interface is working improperly, go to Step 4.

  3. Run the display vrrp6 command to check the configured and running priorities of VRRP6 on the original master and backup routers.

    • Check whether the VRRP6-tracking interface or BFD went Down, and the VRRP6 priority was reduced. If the VRRP6-tracking interface or BFD went Down and the VRRP6 priority was reduced, locate the cause of the fault and restore the faulty link. If the faulty link is restored, go to Step 6.
    • If the VRRP6 tracking interface or BFD is working properly, go to Step 5.

  4. Run the display this interface command in the view of the interface on which VRRP6 is configured to check the physical and protocol status of the interface.

    • If the physical status is Down, the link is faulty. Locate the cause of the fault and restore the link. Then, go to Step 6.
    • If the physical status is Up, check the protocol status. If the protocol status is Down, the IP address of the interface is deleted. Then, go to Step 6.
    • If the protocol status is Up, the IP address of the interface and the virtual IP address of VRRP6 are on different network segments.

  5. Contact technical support personnel. Check whether the configurations of the local and remote ends are correct. If there is any incorrect configuration, correct it.
  6. End.
Translation
Download
Updated: 2019-04-20

Document ID: EDOC1100039602

Views: 124003

Downloads: 90

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next