No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

AR650, AR1600, and AR6100 V300R003

This document describes how to configure and maintain your routers using the web platform.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Physical Interface

Physical Interface

Context

To identify an interface, you can set the description of the interface. You can query and configure physical interfaces based on the site requirements.

Procedure

  • Configuring a physical interface
    1. Choose LAN Access > LAN > Physical Interface, as shown in Figure 11-1.

      Figure 11-1  Physical interface page

    2. In the Modify Interface List area, click corresponding to a physical interface in the Operation column.
    3. In the Modify Physical Interface dialog box, set parameters listed in Table 11-1.

      Table 11-1  Physical interface parameters

      Parameter

      Description

      Interface name

      Name of a physical interface.

      Interface status

      Status of a physical interface: enabled or disabled.

      Description

      Description of a physical interface, for example, HUAWEI, AR Series, GigabitEthernet7/0/0 Interface.

      Working Mode

      Type of a physical interface.

      Current Mode

      Current working mode of a physical interface.

      Auto-negotiation

      By default, auto-negotiation is enabled and the interface rate and duplex mode cannot be configured. If auto-negotiation is disabled, the interface rate and duplex mode can be configured.

      Interface rate

      Transmission of an interface, in Mbit/s.

      Duplex mode

      Duplex mode of an interface, including full duplex and half duplex. By default, the full duplex mode is enabled on an interface. To enable an interface to send and receive packets at the same time, enable the full-duplex mode on the interface. To disable an interface from sending and receiving packets at the same time, enable the half-duplex mode on the interface.

    4. Click OK to save the settings.
  • Viewing detailed information about a physical interface
    1. Choose LAN Access > LAN > Physical Interface, as shown in Figure 11-1.
    2. In the Physical Interface List area, click details corresponding to a physical interface in the Operation column to view detailed information about the physical interface.

  • Switch a physical interface from Layer 2 mode to Layer 3 mode.

    NOTE:

    GE0/0/0 to GE0/0/3 on the AR651W-X4 and AR651-X8 can be changed from Layer 2 mode to Layer 3 mode. GE0/0/0 to GE0/0/7 on the AR651U-A4 , AR1600 and AR6100 series can be changed from Layer 2 mode to Layer 3 mode. GE0/0/0 to GE0/0/5 on the AR651F-Lite can be changed from Layer 2 mode to Layer 3 mode.

    1. Choose LAN Access > LAN > Physical Interface, as shown in Figure 11-1.
    2. In the Physical Interface List area, click corresponding to a physical interface in the Operation column to switch the physical interface between Layer 2 and Layer 3 modes.
    3. In the Information dialog box, click OK. The physical interface switches from Layer 2 mode to Layer 3 mode.

    NOTE:
    • Interfaces supporting switching between Layer 2 and Layer 3 modes cannot be used as access interfaces to connect to the AR platform. Otherwise, when an interface switches between Layer 2 and Layer 3 modes, you may fail to connect to the AR platform.
    • You must delete other configuration on an interface before switching the interface between Layer 2 and Layer 3 modes.

Download
Updated: 2019-04-12

Document ID: EDOC1100041803

Views: 33079

Downloads: 79

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next