No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web-based Configuration Guide

AR650, AR1600, and AR6100 V300R003

This document describes how to configure and maintain your routers using the web platform.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Device Login Through the Web Platform Fails

Device Login Through the Web Platform Fails

Symptom

The device cannot be logged in through the web platform.

Procedure

  1. Check whether the AR and client can ping each other.

    1. Run the ping command on the Windows Command Prompt of the PC to check whether the PC can ping the AR.

      When the system displays the message "Request time out", the target device is unreachable.

    2. Run the display this command in the interface view to check whether the IP address is configured correctly.
    3. If the IP address is incorrect, run the ip address ip-address { mask | mask-length } command in the interface view to reconfigure the IP address.
    4. Open the web platform again and ensure that the input IP address in https://IP address:port is the same as that configured on the AR.

  2. Check whether the browser configuration is correct.

    1. Configure the browser according to Precautions for Using the Web Platform and log in to the web platform again.
    2. Log in to the web platform through another browser and check whether the IE browser limits the login to the web platform.

  3. Check whether the HTTPS server configuration is correct.

    1. Check whether the HTTPS server is enabled.

      Run the display http server command in any view. If the value of HTTPS server status is Disabled, run the http secure-server enable command in the system view to enable the HTTPS server.

    2. Check the port number of the HTTPS server.

      Run the display http server command in any view to check the value of HTTPS server port.

      Ensure that the input port number in the address bar is the same as the value of HTTPS server port.

      Run the http secure-server port command in the system view to configure the port number of the HTTPS server.

  4. Check whether the number of login web users has reached the maximum value.

    Run the display http server command in any view to check values of Current online users and Maximum users allowed.

    If the values of Current online users and Maximum users allowed are the same, log in again after other users go offline.

  5. Check whether the interface that allows access to the web platform is configured.

    Run the display current-configuration filter http server command in any view to check whether there is the configuration of http server permit interface.

    If the interface that allows access to the web platform Is configured and the interface that accesses the web platform is not allowed, run the undo http server permit interface command in the system view to cancel the configuration of the interface that allows access to the web platform or run the http server permit interface command in the system view to reconfigure the interface that allows access to the web platform.

  6. Check whether the web user is configured correctly.

    1. Run the display this command in the AAA view to check whether the web user is correctly configured.
      • If there is the configuration of local-user user-name password irreversible-cipher password, an AAA user with the user name specified by user-name is configured.
      • If there is the configuration of local-user user-name privilege level level, the level of an AAA user with the user name specified by user-name is specified by level.
      • If there is the configuration of local-user user-name service-type http, an AAA user with the user name specified by user-name uses HTTP access.
    2. If any of the preceding configurations is lost, run the following commands in the AAA view as required.
      • Run the local-user user-name password irreversible-cipher password command to set the web user name and password.

      • Run the local-user user-name privilege level level command to set the web user level.

      • Run the local-user user-name service-type http command to configure the service type of the web user to HTTP.

      For example, configure a user with the user name of admin, password of Helloworld@6789, level 15, and HTTP access mode.

      <Huawei> system-view
      [Huawei] aaa
      [Huawei-aaa] local-user admin password irreversible-cipher Helloworld@6789
      [Huawei-aaa] local-user admin privilege level 15
      [Huawei-aaa] local-user admin service-type http
      [Huawei-aaa] quit
      

  7. Check whether access control is configured for the web client.

    1. Run the display current-configuration filter http acl command in any view to check whether there is the configuration of http acl acl-number.

      If there is the configuration of http acl acl-number, record the ACL number.

    2. Run the display acl acl-number command in any view to check whether the IP address of the web client is denied in the ACL.

      If the IP address of the web client is denied in the ACL, run the undo rule rule-id command to delete the ACL rule and use a command to modify the ACL to allow the IP address of the web client.

  8. Check whether the browser is problematic.
Download
Updated: 2019-04-12

Document ID: EDOC1100041803

Views: 31172

Downloads: 71

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next