No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

eSight V300R010C00SPC200, 300, and 500 Local HA System Software Installation Guide (SUSE Linux + Oracle + Veritas) 10

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing the Veritas Software and Database

Installing the Veritas Software and Database

This section describes how to install the Veritas software and database on the eSight server. The operations must be performed on both the active and standby servers.

If the Veritas software is prepared by the customer, the GUI of the VCS client is not supported. In this case, perform the operations on the Veritas CLI.

Procedure

  1. Log in to the eSight server using the management port as the root user.
  2. Run the following commands to install the Veritas software and Oracle database:

    # cd /opt/install/ICMR

    # chmod 700 install.sh

    # sh install.sh -b 192.168.2.100 -m 255.255.255.0 -f 192.168.1.103 -i 192.168.1.100 -l eSightServer -n 255.255.255.0 -s eth2 -e eth1,eth3

    Set parameters next to install.sh based on the site requirements.

    • -b: heartbeat IP address
    • -m: heartbeat subnet mask
    • -f: floating IP address. This parameter is mandatory only for a local HA system.
    • -i: system IP address
    • -l: host name. Set different host names for the active and standby servers.
    • -n: system subnet mask
    • -s: standby system network adapter
    • -e: heartbeat network adapter
    • -z: ICMR option on the distributed server (This parameter is required only when the NTC and WLAN RTLS are deployed in distributed mode.)

  3. Check the Veritas version and patch information.

    1. Check the VxVM software version.

      # rpm -qa | grep VRTSvxvm

      If the VxVM version is correct, the following information is displayed:

      VRTSvxvm-7.1.0.200-SLES12.x86_64 

      If the information next to VRTSvxvm is not 7.1.0.200-SLES12.x86_64, reinstall the Veritas software of version 7.1 or contact Huawei technical support.

    2. Check the VCS software version.

      # rpm -qa | grep VRTSvcs

      If the VCS version is correct, the following information is displayed:

      VRTSvcsag-7.1.0.000-SLES12.x86_64
      VRTSvcs-7.1.0.000-SLES12.x86_64
      VRTSvcsea-7.1.0.000-SLES12.x86_64
      VRTSvcswiz-7.1.0.000-SLES12.x86_64 

      Pay attention to the information next to VRTSvcs. If the information next to VRTSvcs is not 7.1.0.000-SLES12.x86_64, reinstall the Veritas software of version 7.1 or contact Huawei technical support.

  4. Log the root user out of the system and log in to the system as the root user again to make the modified environment variable take effect.
Translation
Download
Updated: 2019-10-30

Document ID: EDOC1100044372

Views: 30212

Downloads: 26

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next