No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

eSight V300R010C00 Maintenance Guide 07

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Changing the IP Address and Host Name of the Single-Node or Distributed System

Changing the IP Address and Host Name of the Single-Node or Distributed System

This section describes how to change the IP address and host name of the single-node or distributed system.

Changing the IP Address for the eSight Server (Windows)

This section describes how to change the IP address of the single-node system on the Windows operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

Ensure the eSight service is stopped. For details, see Stopping eSight.

Changing the Operating System IP Address
  1. Log in to the eSight server as the Administrator user.
  2. Choose Start > Control Panel.
  3. Click Network and Sharing Center in the Control Panel window.

  4. Click Change adapter settings in the Network and Sharing Center dialog box.

  5. Right-click the network connection you want to configure and click Properties in the Network Connections dialog box.

  6. Click Internet Protocol Version 4(TCP/IPv4) and click Properties in the Local Area Connection Properties dialog box.

  7. In the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box, change the IP address, subnet mask, default gateway, and DNS server address as planned.

  8. Click OK.
Synchronizing the System IP Address of eSight

If the system IP address of eSight is changed, you need to synchronously change the system IP address on eSight.

  1. Among all programs, choose eSight > eSight Console.
  2. In the eSight Console dialog box, choose Tools > IP Address Tool

    The IP Address Tool dialog box is displayed.

  3. Select an eSight server IP address and click Modify.
  4. Click Yes in the dialog box that is displayed.

  5. Click Exit.
Synchronizing the Southbound IP Address of eSight

If the southbound IP address of eSight is changed, you need to synchronously modify the southbound IP address on eSight.

  1. Log in to the server as the Administrator user.
  2. Choose Start > All Programs > eSight > eSight Console.
  3. Choose Tools > Southbound IP Config Tool in the eSight Console window.
  4. Configure new Southbound IP and select After modification or rollback, modify the eSight IP address on the device accordingly on the Southbound IP Config Tool page.
NOTE:

If eSight needs to be stopped and started automatically, select Automatically start and stop eSight. Otherwise, you need to manually stop eSight before rollback and start eSight after rollback.

Changing the IP Address of the eSight Server Stored on the Distributed Server

In the southbound and northbound isolation scenario, if the southbound IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server. In the southbound and northbound non-isolation scenario, if the system IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server.

  1. Log in to the distributed server as the Administrator user.
  2. Among all programs, choose eSight > eSight Console. In the eSight Console dialog box that is displayed, click Stop.
  3. In the eSight Console dialog box, choose Tools > Distributed Server Connect Tool.
  4. In the Distributed Server Connect Tool dialog box that is displayed, enter the IP address of the eSight server.

    NOTE:

    In the southbound and northbound isolation scenario, the value of Master IP Address must be the same as the southbound IP address of the active eSight server. In the southbound and northbound non-isolation scenario, the value of Master IP Address must be the same as the system IP address of the active eSight server.

  5. Click Confirm.

    NOTE:

    The system starts to configure the IP address information. During the configuration, do not close the window. Perform operations as prompted.

  6. Click OK.
  7. Click Start in the eSight Console dialog box.

Changing the IP Address and Host Name for the eSight Server (SUSE Linux)

This section describes how to change the IP address and host name of the single-node system on the Linux operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

Ensure the eSight service is stopped. For details, see Stopping the eSight Service.

Changing the Operating System IP Address
  1. Log in to the eSight server as the root user.

    NOTE:

    Remotely log in to the server as the ossuser and switch to the root user if the Linux operating system is hardened.

  2. Run the yast2 command to access the YaST2 Control Center page.
  3. Select Network Devices and click Network Settings.

  4. Configure the IP address in the Network Settings windows.

    1. On the Overview tab, select the IP address you want to change, and click Edit.

    2. On the Address tab page, enter the IP address and subnet mask, and click Next.

    3. Click Hostname/DNS tab, set the DNS server parameters as planned.

    4. Click Routing tab, set the default gateway as planned.

    5. Click OK.

  5. Verify the configuration.

    • Log in to another computer that is connected to the network where the eSight server resides.
    • Choose Start > Run. The Run dialog box is displayed.
    • Enter cmd and click OK. The command-line interface is displayed.
    • Enter ping eSight server IP address in the command terminal window, and then press Enter.

      The command-line interface is displayed. Enter ping eSight server IP address (example: ping 10.137.63.1) and press Enter. If information similar to the following is displayed, the network is configured successfully:

      Pinging 10.137.63.1 with 32 bytes of data:
      Reply from 10.137.63.1: bytes=32 time=16ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
       
      Ping statistics for 10.137.63.1:
      Packets: Sent = 4, Received = 4, Lost = 0 (0% loss);
      Approximate round trip times in milli-seconds:
      Minimum = 0ms, Maximum = 16ms, Average = 4ms
    • Enter exit.

Synchronizing the System IP Address of eSight

If the system IP address of eSight is changed, you need to synchronously modify the system IP address on eSight.

  1. Synchronize the IP address of the server monitored by the Oracle database. Start the listener and ensure the Oracle database is running properly.

    For details about how to synchronize the IP address of the server monitored by the Oracle database, see How Do I Check and Modify the Server IP Address Monitored by the Oracle Database?

  2. Log in to the eSight server as the ossuser user.
  3. Run the following commands to start the IP address tool:

    > cd /opt/eSight/mttools/tools

    > ./ipchange.sh

    The IP Address Tool dialog box is displayed.

  4. Select an eSight server IP address and click Modify.
  5. Click Yes in the dialog box that is displayed.

  6. Click Exit.
  7. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Synchronizing the Southbound IP Address of eSight

If the southbound IP address of eSight is changed, you need to synchronously modify the southbound IP address on eSight.

  1. Log in to the server as the ossuser user.
  2. Run the following command to start Southbound IP Config Tool:
    • > cd /opt/eSight/mttools/tools
    • > ./southip.sh The Southbound IP Config Tool dialog box is displayed.
  3. Configure new Southbound IP and select After modification or rollback, modify the eSight IP address on the device accordingly on the Southbound IP Config Tool page and click OK.
  4. Restart eSight.
Changing the IP Address of the eSight Server Stored on the Distributed Server

In the southbound and northbound isolation scenario, if the southbound IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server. In the southbound and northbound non-isolation scenario, if the system IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server.

  1. Log in to the distributed server as the ossuser user.
  2. Run the following commands to stop the eSight service.

    > cd /opt/eSight/bin

    > ./shutdown.sh

    When the status of every process is STOPPED and "stopping eSight system succeeded." is displayed, the eSight service has been stopped.

  3. Run the following commands to open the Distributed Server Connect Tool.

    > cd /opt/eSight/mttools/tools

    > ./connect_tool.sh

  4. In the Distributed Server Connect Tool dialog box that is displayed, enter the IP address of the eSight server.

    NOTE:

    In the southbound and northbound isolation scenario, the value of Master IP Address must be the same as the southbound IP address of the active eSight server. In the southbound and northbound non-isolation scenario, the value of Master IP Address must be the same as the system IP address of the active eSight server.

  5. Click Confirm.

    NOTE:

    The system starts to configure the IP address information. During the configuration, do not close the window. Perform operations as prompted.

  6. Click OK.
  7. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Changing the IP Address and Host Name for the eSight Server (EulerOS)

This section describes how to change the IP address and host name of the single-node system on the Euler operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

The eSight service has been stopped. For details about how to stop the eSight service, see Stopping the eSight Service.

Changing the Operating System IP Address
  1. Log in to the server as the root user.
  2. Run the following command to modify the server IP address:

    sem_tool -cmd ifconfig -name eth2 -ip 10.137.63.1 -mask 255.255.254.0 -gateway 10.137.116.1

    Parameter

    Level-2 Parameter

    Description

    ifconfig

    -name

    NIC name.

    -ip

    IP address to be configured.

    -mask

    Subnet mask.

    -gateway

    Gateway.

  3. Verify the configuration.

    • Log in to another computer that is connected to the network where the eSight server resides.
    • Choose Start > Run. The Run dialog box is displayed.
    • Enter cmd and click OK. The command-line interface is displayed.
    • Enter ping eSight server IP address in the command terminal window, and then press Enter.

      For example, after you run the ping 10.137.63.1 command, if information similar to the following is displayed, the network is configured successfully:

      Pinging 10.137.63.1 with 32 bytes of data:
      Reply from 10.137.63.1: bytes=32 time=16ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
       
      Ping statistics for 10.137.63.1:
      Packets: Sent = 4, Received = 4, Lost = 0 (0% loss);
      Approximate round trip times in milli-seconds:
      Minimum = 0ms, Maximum = 16ms, Average = 4ms
    • Enter exit.

Synchronizing the System IP Address of eSight

If the system IP address of eSight is changed, you need to synchronously modify the system IP address on eSight.

  1. Log in to the server as the ossuser user.
  2. Run the following command to go to the target directory:

    cd eSight installation directory/mttools/tools

  3. Change the IP address using commands.

    es_cli -cmd ipchange 10.137.63.1

  1. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Synchronizing the Southbound IP Address of eSight

If the southbound IP address of eSight is changed, you need to synchronously modify the southbound IP address on eSight.

  1. Log in to the server as the ossuser user.
  2. Run the following command to start Southbound IP Config Tool:
    • > cd /opt/eSight/mttools/tools
    • > ./southip.sh The Southbound IP Config Tool dialog box is displayed.
  3. Configure new Southbound IP, select After modification or rollback, modify the eSight IP address on the device accordingly on the Southbound IP Config Tool page, and click OK.
  4. Restart eSight.
Changing the IP Address of the eSight Server Stored on the Distributed Server

In the southbound and northbound isolation scenario, if the southbound IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server. In the southbound and northbound non-isolation scenario, if the system IP address of the eSight server is changed, you need to change the eSight server IP address stored on the NTC server.

  1. Log in to the distributed server as the ossuser user.
  2. Run the following commands to stop the eSight service.

    > cd /opt/eSight/bin

    > ./shutdown.sh

    When the status of every process is STOPPED and "stopping eSight system succeeded." is displayed, the eSight service has been stopped.

  3. Run the following commands to open the Distributed Server Connect Tool.

    > cd /opt/eSight/mttools/tools

    > ./connect_tool.sh

  4. In the Distributed Server Connect Tool dialog box that is displayed, enter the IP address of the eSight server.

    NOTE:

    In the southbound and northbound isolation scenario, the value of Master IP Address must be the same as the southbound IP address of the active eSight server. In the southbound and northbound non-isolation scenario, the value of Master IP Address must be the same as the system IP address of the active eSight server.

  5. Click OK.

    NOTE:

    The system starts to configure the IP address information. During the configuration, do not close the window. Perform operations as prompted.

  6. Click OK.
  7. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Changing the IP Address for the Distributed Server (Windows)

This section describes how to change the IP address of the distributed server on the Windows operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

Ensure the eSight service is stopped on the distributed server. For details, see Stopping eSight.

Changing the Operating System IP address
  1. Log in to the distributed server as the Administrator user.

    NOTE:

    If security hardening has been performed for the Windows operating system, you need to log in to the server as the SWMaster user.

  2. Choose Start > Control Panel.
  3. Click Network and Sharing Center in the Control Panel window.

  4. Click Change adapter settings in the Network and Sharing Center dialog box.

  5. Right-click the network connection you want to configure and click Properties in the Network Connections dialog box.

  6. Click Internet Protocol Version 4(TCP/IPv4) and click Properties in the Local Area Connection Properties dialog box.

  7. In the Internet Protocol Version 4 (TCP/IPv4) Properties dialog box, change the IP address, subnet mask, default gateway, and DNS server address as planned.

  8. Click OK.
Synchronize the Server IP Address to Distributed Service
  1. Among all programs, choose eSight > eSight Console.
  2. In the eSight Console dialog box, choose Tools > IP Change Tool.

    The IP Address Tool dialog box is displayed.

  3. Select a server IP address and click Modify.
  4. Click Yes in the dialog box that is displayed.
  5. Click Exit.

Changing the IP Address and Host Name for the Distributed Server (Linux)

This section describes how to change the IP address and host name of the distributed server on the Linux operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

Ensure the eSight service is stopped on the distributed server. For details, see Stopping the eSight Service.

Changing the Operating System IP address
  1. Log in to the distributed server as the root user.

    NOTE:

    Remotely log in to the server as the ossuser and switch to the root user if the Linux operating system is hardened.

  2. Run the yast2 command to access the YaST2 Control Center page.
  3. Select Network Devices and click Network Settings.

  4. Configure the IP address in the Network Settings windows.

    1. On the Overview tab, select the IP address you want to change, and click Edit.

    2. On the Address tab page, enter the IP address and subnet mask, and click Next.

    3. Click Hostname/DNS tab, set the DNS server parameters as planned.

    4. Click Routing tab, set the default gateway as planned.

    5. Click OK.

  5. Verify the configuration.

    • Log in to another computer that is connected to the network where the eSight server resides.
    • Choose Start > Run. The Run dialog box is displayed.
    • Enter cmd and click OK. The command-line interface is displayed.
    • Enter ping eSight server IP address in the command terminal window, and then press Enter.

      For example, after you run the ping 10.137.63.1 command, if information similar to the following is displayed, the network is configured successfully:

      Pinging 10.137.63.1 with 32 bytes of data:
      Reply from 10.137.63.1: bytes=32 time=16ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
       
      Ping statistics for 10.137.63.1:
      Packets: Sent = 4, Received = 4, Lost = 0 (0% loss);
      Approximate round trip times in milli-seconds:
      Minimum = 0ms, Maximum = 16ms, Average = 4ms
    • Enter exit.

Synchronize the Server IP Address to Distributed Service
  1. Log in to the distributed server as the ossuser user.
  2. Use the IP address change tool to synchronize the distributed server IP address.

    > cd /opt/eSight/mttools/tools

    > ./ipchange.sh

    The IP Address Tool dialog box is displayed.

  3. Select a server IP address and click Modify.
  4. Click Yes in the dialog box that is displayed.
  5. Click Exit.
  6. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Changing the IP Address and Host Name for the Distributed Server (Euler Operating System)

This section describes how to change the IP address and host name of the distributed server on the Euler operating system. After changing the IP address of the operating system, you need to change the IP address configuration of related systems.

Prerequisites

The eSight service has been stopped. For details about how to stop the eSight service, see Stopping the eSight Service.

Changing the Operating System IP Address
  1. Log in to the server as the root user.
  2. Run the following command to modify the server IP address:

    sem_tool -cmd ifconfig -name eth2 -ip 10.137.63.1 -mask 255.255.254.0 -gateway 10.137.116.1

    Parameter

    Level-2 Parameter

    Description

    ifconfig

    -name

    NIC name.

    -ip

    IP address to be configured.

    -mask

    Subnet mask.

    -gateway

    Gateway.

  3. Verify the configuration.

    • Log in to another computer that is connected to the network where the eSight server resides.
    • Choose Start > Run. The Run dialog box is displayed.
    • Enter cmd and click OK. The command-line interface is displayed.
    • Enter ping eSight server IP address in the command terminal window, and then press Enter.

      For example, after you run the ping 10.137.63.1 command, if information similar to the following is displayed, the network is configured successfully:

      Pinging 10.137.63.1 with 32 bytes of data:
      Reply from 10.137.63.1: bytes=32 time=16ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
      Reply from 10.137.63.1: bytes=32 time<1ms TTL=252
       
      Ping statistics for 10.137.63.1:
      Packets: Sent = 4, Received = 4, Lost = 0 (0% loss);
      Approximate round trip times in milli-seconds:
      Minimum = 0ms, Maximum = 16ms, Average = 4ms
    • Enter exit.

Synchronizing the System IP Address of eSight

If the system IP address of eSight is changed, you need to synchronously modify the system IP address on eSight.

  1. Log in to the server as the ossuser user.
  2. Run the following command to go to the target directory:

    cd eSight installation directory/mttools/tools

  3. Change the IP address using commands.

    es_cli -cmd ipchange 10.137.63.1

  1. Start the eSight service.

    > cd /opt/eSight/bin

    > ./startup.sh

Translation
Download
Updated: 2019-06-30

Document ID: EDOC1100044373

Views: 25085

Downloads: 74

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next