No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

eSight V300R010C00SPC200, 300, and 500 Operation Guide 09

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Adding GPON Devices

Adding GPON Devices

This topic describes how to add devices to the eSight to realize unified management.

Operation Procedure

Step

Operation

Description

1

Set protocol parameters on the device: SNMP.

For details, see Setting Protocol Parameters on the Device.

2

Set protocol parameters on eSight: SNMP.

For details, see Setting SNMP Parameters on eSight.

Protocol parameter values on eSight must be consistent with those on the device.

3

Add devices to eSight.

For details, see Adding OLTs and ONUs.

Setting Protocol Parameters on the Device

This topic describes how to set protocol parameters on the device. The following uses MA5600T V800R017C10 as an example to describe the configuration. For commands of other device models, see the configuration manual.

Configuring the SNMP Protocol

The SNMP protocol is used to add devices to eSight.

NOTE:

SNMP v3 is recommended because its security level is higher than that of SNMP v1 and SNMP v2c.

  • SNMP v3
    huawei(config)#snmp-agent sys-info version v3
    huawei(config)#snmp-agent mib-view View_ALL include iso   //View_ALL indicates the name of the MIB view. To ensure that eSight can properly manage devices (for example, discover device links through the LLDP protocol), the MIB view must contain the iso node.
    huawei(config)#snmp-agent group v3 snmpv3group privacy write-view View_ALL notify-view View_ALL   //snmpv3group is the configured user group. The write view name and notification view name is specified as View_ALL. By default, the write view has the read permission. Therefore, you do not need to set the read-view. The notification view is used to limit the MIB node of the device for sending alarms to eSight. 
    huawei(config)#snmp-agent group v3 snmpv3group privacy   //snmpv3group is the specified user group.
    huawei(config)#snmp-agent usm-user v3 snmpv3user group snmpv3group   //snmpv3user is the configured user name, which is consistent with the security name of eSight. The security level of a user cannot be lower than the security level of the user group to which the user belongs. Otherwise, the user cannot perform communication normally. For example, if the security level of the user group snmpv3group is privacy, the security level of the user snmpv3user must be authentication and encryption. 
    huawei(config)#snmp-agent usm-user v3 snmpv3user snmpv3group authentication-mode sha authkey123 privacy-mode aes128 prikey123   //Set the encryption protocol and password of the user, and ensure that the encryption protocol and password are the same as those of eSight.
    huawei(config)#snmp-agent trap enable snmp-agent target-host trap-paramsname aaa v3 securityname snmpv3user authentication   //Assume aaa is the list name, snmpv3user is the security name, and the trap packet is authenticated but is not encrypted.
    huawei(config)#snmp-agent target-host trap-hostname V3 address 10.10.10.10 udp-port 162 trap-paramsname aaa  //Assume user is the host name, 10.10.10.10 is the destination IP address of the target host that receives the trap packet. 162 is the port, aaa is the name of the sending parameter list of the trap packet.
  • SNMP v2c
    huawei(config)#snmp-agent community read public123 //public123 is the specified read community.
    huawei(config)#snmp-agent community write private123 //private123 is the specified write community.
    huawei(config)#snmp-agent trap enable standard
    huawei(config)#snmp-agent target-host trap-paramsname aaa v2c securityname bbb //Assume aaa is the list name, bbb is the security name.
    huawei(config)#snmp-agent target-host trap-hostname user address 10.10.10.10 udp-port 162 trap-paramsname aaa //Assume user is the host name, 10.10.10.10 is the destination IP address of the target host that receives the trap packet. 162 is the port, aaa is the name of the sending parameter list of the trap packet.
  • SNMP v1
    huawei(config)#snmp-agent community read public123 //public123 is the specified read community.
    huawei(config)#snmp-agent community write private123 //private123 is the specified write community.
    huawei(config)#snmp-agent trap enable standard
    huawei(config)#snmp-agent target-host trap-paramsname aaa v1 securityname bbb //Assume aaa is the list name, bbb is the security name.
    huawei(config)#snmp-agent target-host trap-hostname user address 10.10.10.10 udp-port 162 trap-paramsname aaa //Assume user is the host name, 10.10.10.10 is the destination IP address of the target host that receives the trap packet. 162 is the port, aaa is the name of the sending parameter list of the trap packet.

Setting SNMP Parameters on eSight

This section describes how to set SNMP parameters so that devices and eSight can communicate properly. You can use templates to set SNMP parameters for multiple devices at a time.

Prerequisites

SNMP parameters have been correctly set on devices.

Procedure

  1. Choose Resource > Common from the main menu.
  2. Choose Add Resource > Protocol Template > SNMP Template from the navigation tree on the left.
  3. Click Create and set template parameters on the displayed page.

    • SNMPv3

    • SNMPv2c

    • SNMPv1

    NOTE:
    • The SNMP parameter settings on eSight must be the same as those on devices.
    • Using SNMPv3 is recommended because of its higher security than SNMPv1 and SNMPv2c.
    Table 18-1 SNMP parameters on eSight and devices

    SNMP Parameters on eSight

    SNMP Parameters on Devices

    Authentication password

    Authentication password

    Privacy protocol

    User encryption mode

  4. Click OK.

Adding OLTs and ONUs

This topic describes how to add OLTs and ONUs to the eSight to realize central management.

Context

  • eSight considers both ONU and ONT as ONU.
  • An OLT device maintains information about ONUs connected to it. After an OLT is added to eSight, OLT basic information, links between the OLT and ONUs, and ONUs connected to the OLT are automatically added to eSight.
  • Some ONU devices support SNMP parameters and require refined device management in terms of device panel, interface information, and other aspects. After you add an OLT to eSight, you need to manually add these ONU devices to meet O&M requirements. The methods for adding ONUs are the same as those for Adding OLTs.

Adding OLTs

You can use either of the following methods shown in Table 18-2 to add OLTs to eSight like common devices.

Table 18-2 Adding devices to eSight

Method

Application Scenario

(Recommended) Automatically discovering devices

eSight can automatically discover devices on a network immediately or as scheduled by IP address segment or using SNMP or Internet Control Message Protocol (ICMP).

Importing devices in batches

You can import devices from an existing device list, which contains basic device information, including the device IP address and protocol parameters, such as the protocol type and version.

Adding a single device

This method can be used to add a small number of devices to eSight.

Related Operations

Synchronize OLT and ONU information. After you add OLTs and ONUs to eSight, the following information may change during the network maintenance process.

  • Basic OLT information
  • Connections between OLTs and ONUs
  • Basic ONU information and the number of ONUs connected to each OLT

The periodic synchronization function provided by eSight can only synchronize basic OLT information. You are advised to manually synchronize OLT and ONU information to eSight.

  1. Choose Resource > PON from the main menu.
  2. Choose PON Resource > Device from the navigation tree on the left.
  3. Select the OLT device, and click Synchronize.

Automatically Discovering NEs

This topic describes how to configure eSight to automatically discover OLTs and MxUs using IP addresses.

Prerequisites

  • eSight and NEs can ping each other successfully.
  • You have the operation rights for Access Resource.
  • SNMP parameters have been correctly set on NEs.
  • SNMP parameters have been correctly set on eSight, and must be the same as those on NEs.

Context

The eSight provides three automatic device discovery modes by network segment, by ARP, and by router. You can also add network segments or IP addresses of the devices that do not need to be discovered to an exclusion list. During automatic device discovery, the eSight automatically skips the network segments or IP addresses in the exclusion list.

Automatic discovery tasks are classified into one-off tasks and scheduled tasks. One-off tasks are executed immediately while you can determine whether to execute scheduled tasks immediately.

Procedure

  1. Choose Resource > Add Resource > Automatic Task Management from the main menu.
  2. On the Exclusion List tab page, check the excluded network segments or IP addresses.

    Add the network segments or IP addresses of the devices that do not need to be discovered to the exclusion list. The task will automatically skip the network segments or IP addresses.

  3. Choose Resource > Add Resource > Auto Discovery from the main menu.
  4. On the Auto Discovery tab, click Change Discovery Mode in the upper right corner to select a desired mode.
  5. Set the parameters of an automatic discovery task and click Auto Discovery.
  6. Confirm the discovery results.

    • You can immediately view the results for the task with type as Once-off and the scheduled task that is immediately executed.
    • For the scheduled task that is not immediately executed, Choose Add Resource > Automatic Task Management from the navigation tree on the left and view the discovery results in Discovered Device List.

Importing Devices in Batches

This section describes how to import devices in batches by using Excel files.

Prerequisites

  • eSight and devices can ping each other successfully.
  • SNMP parameters have been correctly set on devices.
  • SNMP parameters have been correctly set on eSight, and must be the same as those on devices.

Procedure

  1. Choose Resource > Common from the main menu.
  2. Choose Add Resource > Import Resource from the navigation tree on the left.
  3. On the Import Resource tab page, choose Access Device > SNMP.
  4. Click next to Download Template to download the template.
  5. Open the template, enter device information, and save the file.

    NOTE:
    • Protocol parameters in the Excel files must be consistent with those configured on devices.
    • You can use the offline import function to add unpowered devices to eSight. After the devices are powered on, eSight can normally manage the devices.

  6. On the Import Resource page, click next to Upload Resource File and select a template to be uploaded.
  7. Click to upload the template.

    Device information and device check results are displayed on the right of the page. If Result is empty, device check succeeds.

  8. Select a device and click Create.

    • If the device is created successfully, the Result column is The resource is created successfully.
    • If the device cannot be created, the reason for the failure is displayed in the Result column. You can attempt to solve the problem and import devices again based on the failure reason. If the fault persists, contact the technical support personnel.

Follow-up Procedure

After devices are added to eSight successfully, you can view them by choosing Resource > PON > PON Resource > Device from the main menu.

Adding an OLT

This section describes how to add an OLT to eSight. This method can be used to add a small number of devices to eSight.

Prerequisites

  • eSight and devices can ping each other successfully.
  • When adding devices through SNMP, you need to obtain the SNMP protocol of the devices.

Procedure

  1. Choose Resource > Common from the main menu.
  2. Choose Add Resource > Add Resource from the navigation tree on the left.
  3. On the Add Resource tab page, click Access Device.
  4. Set related parameters.

    Table 18-3 SNMP parameters on eSight and devices

    SNMP Parameters on eSight

    SNMP Parameters on Devices

    Security name

    User Name

    Authentication password

    Authentication password

    Privacy protocol

    User encryption mode

  5. Click OK.

    • If the device is added successfully, you can view the NE in the managed object list.
    • If the device cannot be added, the failure reason is displayed in the Error dialog box that is displayed. Click OK and set the parameters again.

Adding an ONU

This section describes how to add a single ONU to eSight. This method can be used to add a small number of NEs to eSight.

Prerequisites

  • eSight is running properly.
  • An OLT has been added to eSight.
  • A multi-service profile has been created.

Procedure

  1. Choose Resource > PON from the main menu.
  2. Choose PON Resource > ONU from the navigation tree on the left.
  3. Click .
  4. In the Create ONU dialog box, set Home OLT, Home PON port, ONU ID, ONU Type, MultiService templates, SN and ONU Alias.

    NOTE:

    For one port of an OLT, SN and ONU ID cannot be the same as existing SN or ONU ID when creating ONU.

  5. Click OK. An ONU record is added to ONU list.

Adding a POS

A passive optical splitter (POS) is a passive component that connects the OLT and ONUs. It splits one channel of optical signals into multiple channels without external energy. It centralizes upstream data and delivers downstream data. eSight cannot directly monitor the POS because it is a passive device. You need to manually add the POS to eSight and establish connections between the POS and OLT and ONU. eSight cannot automatically detect connection changes between the POS and OLT and ONU, and you need to maintain the connections manually.

Prerequisites

The OLT and all the ONUs connected to the OLT have been added or synchronized to eSight. For details, see Adding OLTs and ONUs.

Context

The POS is connected to the PON interface of the OLT. After OLTs are added to eSight, eSight allocates a POS named Splitter(L1) for the PON interface of each OLT by default.

Procedure

  • Add POSs in batches.
    1. Choose Resource > PON from the main menu.
    2. Choose PON Resource > Splitter from the navigation tree on the left.
    3. Click .
    4. Click to save the template to the local device.
    5. Open the downloaded template, set OLT IP, OLT Port, SN Number, Splitter Level, and Splitter Name, and then save the modified template.
    6. Click , select the modified template, click and then click Confirm.
  • Add a single POS.
    1. Choose Resource > PON from the main menu.
    2. Choose PON Resource > Splitter from the navigation tree on the left.
    3. Click next to the GPON interface to which a POS is to be added.
    4. On the page that is displayed, set related parameters and click Confirm.
Translation
Download
Updated: 2019-09-12

Document ID: EDOC1100044378

Views: 82327

Downloads: 403

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next