No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

eSight V300R010C00 Operation Guide 08

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Operation Panorama

Operation Panorama

The eLTE operation panorama describes management operations in diverse O&M scenarios. Users can perform appropriate operations based on actual O&M scenarios.

Figure 19-1 Operation Panorama
Table 19-1 Operation description

Device

Scenario

Task

Operation Description

Industry Terminal

Site deployment

Configuring a Southbound IP Address

The interface between eSight and industry terminals is a southbound one. A southbound interface IP address must be configured for eSight to manage industry terminals. For details, see Configuring a Southbound IP Address.

Enabling eSight Login via Multiple Subnets

If industry terminals are deployed in different subnets, enable multi-subnet eSight access. For details, see section "Configuring Multi-Subnet Management" in the eSight Software Installation Guide.

NOTE:

You do not need to configure this item if industry terminals are deployed within the same subnet.

Adding a Route from eSight to an Industry Terminal

For details, see Adding a Route from the eSight to an Industry Terminal.

Configuring DNS Server

Configuring a DNS Server A DNS server allocates domain name addresses and IP addresses to hosts. The DNS server is required for the management and configuration of industry terminal networking. For details, see Configure the DNS Server.

NOTE:

The default auto-configuration server (ACS) address of the industry terminal is acs.inner.net. The domain name of the industry terminal is acs.inner.net, and the corresponding IP address is the southbound IP address of eSight.

Configuring NTP Server

(Optional) Configuring NTP Server To synchronize the time between eSight and devices, configure the eSight server as the Network Time Protocol (NTP) server. The NTP server is optional for eSight. You need to configure the NTP server only when the eLTE component is installed and eSight needs to function as the network clock source. For details, see section "(Optional) Configuring the NTP Server" in eSight Software Installation Guide.

NOTE:

If any problem occurs when configuring the NTP server, you need to roll back the configuration first. And then configuring NTP server again.

Applying for and Importing a License File

A trial license is provided by eSight and is available within 90 days. After the trial license expires, a new eSight license must be purchased. For details about how to apply for and load a commercial license, see section "Applying for and Loading an eSight License" in eSight Software Installation Guide.

Adding Industry Terminal

  • Adding a Single industry terminal

    Enter the device information and add devices one by one. For details, see Adding a Single eLTE Device.

  • Adding industry terminals in batches

    Import device information using the template to add devices in batches. For details, see Adding eLTE Devices in Batches.

Authorizing an Untrusted Industry Terminal

After devices are powered on, device information is displayed in the untrusted industry terminal list. Select the devices and click Trust. Then, the devices are moved to the industry terminal list as managed objects. For details, see Untrusted Industry Terminal.

Uploading an Industry Terminal Software Version to eSight

You can upload a local industry terminal software version file to eSight and change version information. In addition, you can select a firmware version and then upgrade an industry terminal to the selected version. For details, see Industry Terminal Version Management.

Uploading an Industry Terminal Configuration File

You can upload a local industry terminal configuration file to eSight and change the basic information in the configuration file. In addition, you can select a configuration file and enable an industry terminal to use the selected configuration file. For details, see Configuration File.

Automatic Industry Terminal Deployment (PnP)

After an industry terminal is powered on for the first time, it automatically connects to eSight and triggers registration, firmware version upgrade, and configuration file delivery. For details, see Global Parameters.

Scenario

Manage Industry Terminals

On the industry terminal management page, users can delete devices, check the device list, manage industry terminal logs, and ping, restart, and reset industry terminals. For details, see Industry Terminal.

On the industry terminal management page, users can click an industry terminal name to enter the industry terminal homepage where users can check industry terminal details and set parameters. For details, see Basic Configuration.

NOTE:

The industry terminal number that displayed in portal only contains the number of online industry terminals and offline industry terminals.

eNodeB

Site deployment

Applying for and Importing a License File

A trial license is provided by eSight and is available within 90 days. After the trial license expires, a new eSight license must be purchased. For details about how to apply for and load a commercial license, see section "Applying for and Loading an eSight License" in eSight Software Installation Guide.

Adding eNodeB

  • Auto Discovery for eNodeBs

    You can apply the automatic device discovery function to discover devices in batches if all devices in an IP network segment need to be connected to and establish communication with eSight. The function saves time. For details, see Auto Discovery for Devices.

  • Adding a Single eNodeB

    Enter the device information and add devices one by one. For details, see Adding a Single eLTE Device.

  • Adding eNodeBs in batches

    Import device information using the template to add devices in batches. For details, see Adding eLTE Devices in Batches.

Uploading an eNodeB Software Version to eSight

You can upload a local eNodeB software version file to eSight and change version information. In addition, you can select a firmware version and then upgrade a eNodeB to the selected version. For details, see 1.6.4 eNodeB Version Management.

Scenario

Manage eNodeBs

On the eNodeB management page, users can add and delete eNodeBs, and synchronize configuration. For details, see eNodeB.

On the eNodeB management page, users can click an eNodeB name to enter the eNodeB homepage where users can check basic information and manage eNodeB resources.

eSE

Site deployment

Applying for and Importing a License File

A trial license is provided by eSight and is available within 90 days. After the trial license expires, a new eSight license must be purchased. For details about how to apply for and load a commercial license, see section "Applying for and Loading an eSight License" in eSight Software Installation Guide.

Adding eSE

Scenario

Managing eSEs

On the eSE management page, users can add and delete eSEs, and synchronize configuration. For details, see eSE. On the eSE management page, users can click a eSE name to enter the eSE homepage where users can check devices details.

Translation
Download
Updated: 2019-08-03

Document ID: EDOC1100044378

Views: 64046

Downloads: 344

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next