No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Web Online Help

TE10 Videoconferencing Endpoint V600R019C00

This document describes the help information on the web interface.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Setting TR-069 Parameters

Setting TR-069 Parameters

Set CPE WAN Management Protocol (CWMP) TR-069 parameters to centrally manage endpoints.

Procedure

  1. Choose System Settings > Network and click the TR069 tab.
  2. Set the TR-069 parameters listed in Table 3-19.

    Table 3-19  TR-069 parameters

    Parameter

    Description

    Setting

    TR069

    Specifies whether to enable the TR-069 function. If this function is enabled, the endpoint will send a session setup request to the Auto-Configuration Server (ACS). Start the ACS before enabling the TR-069 function.

    NOTE:

    If you set this parameter to Enable, you must also set ACS user name, ACS password, ACS server IP address, Report interval(s), CPE user name, CPE password, and Authentication mode.

    The default value is Disable.

    ACS user name

    Specifies the user name authenticated by the ACS after receiving a session setup request from the endpoint. The user name has been specified on the ACS.

    The default value is eSight.

    ACS password

    Specifies the password authenticated by the ACS after receiving a session setup request from the endpoint The password has been specified on the ACS.

    The default value is eSight*123.

    ACS server IP address

    Specifies the ACS URL, which can be based on an IP address or domain name.
    • If an IP address is used, the value must be in the format of https://eSight IP address:8444/tr069/services/acs.
    • If a domain name is used, the value must be in the format of https://eSight domain name:8444/tr069/services/acs.

    No default value is set for this parameter.

    Report interval(s)

    Specifies the interval at which the endpoint sends a session setup request to the ACS.

    The default value is 1800.

    It is recommended that this interval be shorter than the timeout period of the ACS. If this interval is longer than the timeout period, the ACS may be disconnected or the session status may not be updated in time after a session setup timeout.

    CPE user name

    Specifies the user name authenticated by the endpoint after receiving a session setup request from the ACS. The user name has been specified on the ACS.

    The default value is admin.

    CPE password

    Specifies the password authenticated by the endpoint after receiving a session setup request from the ACS. The password has been specified on the ACS.

    In addition, it must include at least two of the following: uppercase letters, lowercase letters, digits, and special characters.

    Authentication mode

    Specifies the mode in which the endpoint will be authenticated when accessing to the network management system.

    The default value is Digest.

    If you set this parameter to None or Basic, the system will prompt you that the authentication mode poses security risks. For security purposes, set this parameter to Digest.

    The default value is recommended.

    STUN

    Specifies whether to enable the Simple Traversal of UDP through NAT (STUN) function. If this function is enabled, the endpoint can perform private-to-public network traversal using the STUN server on the TR-069 network.

    NOTE:

    If you set this parameter to Enable, you must also set STUN server IP address, STUN server port, STUN listen port, STUN user name, STUN password, and STUN keepalive period (s).

    The default value is Disable.

    STUN server IP address

    Specifies the IP address of the STUN server.

    No default value is set for this parameter.

    Obtain the value of this parameter from the STUN server administrator.

    STUN server port

    Specifies the port number used by the STUN server to provide the private and public network traversal service.

    The default value is 3478.

    Obtain the value of this parameter from the STUN server administrator.

    STUN listen port

    Specifies the port provided by the endpoint for private and public service interaction with the STUN server.

    The default value is 3000.

    STUN user name

    STUN password

    Specifies the authentication user name and password of the STUN server.

    No default value is set for this parameter.

    Obtain the value of this parameter from the STUN server administrator.

    It is recommended that the password contain at least 16 characters that consist of letters, digits, and special characters.

    STUN keepalive period (s)

    Specifies the interval at which the endpoint sends a session setup request to the STUN server.

    The default value is 150.

    Log collection

    Specifies whether the endpoint allows eSight to collect its logs.

    The default value is Enable.

    CHR collection

    Specifies whether to enable the call history record (CHR) collection function for the endpoint.

    After this function is enabled, the endpoint automatically collects call information and generates session and media CHR data and periodically reports the media CHR data to eSight.

    The default value is Enable.

    CHR collection interval

    Specifies the interval at which the endpoint collects CHR data.

    The default value is 300.

    CHR reporting interval

    Specifies the interval at which the endpoint reports media CHR data to eSight.

    The default value is 300.

  3. Click Save to make the settings take effect.
Translation
Download
Updated: 2019-10-22

Document ID: EDOC1100044672

Views: 13845

Downloads: 16

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next