No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Basic Storage Service Configuration Guide for Block

OceanStor Dorado V3 Series V300R002

This document is applicable to OceanStor Dorado3000 V3, Dorado5000 V3, Dorado6000 V3, and Dorado18000 V3. It describes the basic storage services and explains how to configure and manage them.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Modifying an Ethernet Port

Modifying an Ethernet Port

When the networking mode between a storage device and an application server changes, modify the settings of Ethernet port parameters to ensure proper communication between them.

Precautions

  • Change the IP address of an Ethernet port only when necessary. Before changing the IP address of an Ethernet port, either ensure that redundant connections are available or stop services carried by this port.
  • The IP addresses of an Ethernet port and internal heartbeat must be on different network segments.

    The default IP addresses of internal heartbeat on a dual-controller storage system are 127.127.127.10 and 127.127.127.11, and the default IP addresses of internal heartbeat on a four-controller storage system are 127.127.127.10, 127.127.127.11, 127.127.127.12, and 127.127.127.13.

  • Internal heartbeat links are established between controllers for the controllers to detect each other's working status. Heartbeat links do not require separate cable connections. Internal heartbeat IP addresses are assigned before delivery and cannot be changed.
  • The IP address of an Ethernet port must not be in the same network segment as that of a management network port.
  • The IP address of an Ethernet port must not be in the same network segment as that of a maintenance network port. The default IP address of the maintenance network port must fall within the 172.31.XXX.XXX segment.
  • If an Ethernet port connects to an application server, the IP address of the Ethernet port must be in the same network segment as that of the service network port on the application server. If an Ethernet port connects to another storage device, the IP address of the Ethernet port must be in the same network segment as that of the peer Ethernet port on the other storage device. If available IP addresses are insufficient for a network segment for which you want to add an IP address, add routes.
  • After Ethernet ports are bonded, their properties cannot be modified.

Procedure

  1. Choose System.
  2. Click the controller enclosure where the Ethernet port resides.
  3. Click to switch to the rear view.
  4. Click the Ethernet port whose information you want to modify.

    The Ethernet Port dialog box is displayed.

  5. Modify the Ethernet port.

    1. Click Modify.
      NOTE:

      You can also click Properties to modify the parameters of the Ethernet port.

    2. In the Work Mode drop-down list, select a work mode of the Ethernet port.
      NOTE:

      This parameter can be configured for only ports of I/O modules whose model is 65 (4-port SmartIO module), 66 (4-port SmartIO module), 67 (2-port 100GE/40GE I/O module), or 68 (2-port 100GE/40GE I/O module).

    3. Specify IPv4 Address or IPv6 Address.
    4. Specify Subnet Mask or Prefix.
    5. Specify MAC Address.
    6. Specify MTU (Byte).

  6. Confirm the Ethernet port modification.

    1. Click Apply.

      A security alert dialog box is displayed.

    2. Confirm the information in the dialog box and select I have read and understand the consequences associated with performing this operation.
    3. Click OK.

      The Success dialog box is displayed, indicating that the operation is successful.

    4. Click OK.

Translation
Download
Updated: 2019-07-17

Document ID: EDOC1100049139

Views: 30450

Downloads: 225

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next