No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference for Block

OceanStor Dorado V3 Series V300R002

This document is applicable to OceanStor Dorado3000 V3, Dorado5000 V3, Dorado6000 V3 and Dorado18000 V3. Based on the CLI provided by the DeviceManager, this document describes how to use various commands classified by functions and how to set the CLI and manage the storage system through these commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
show hyper_metro_pair general

show hyper_metro_pair general

Function

The show hyper_metro_pair general command is used to query HyperMetro pairs.

Format

show hyper_metro_pair general pair_id=?

Parameters

Parameter

Description

Value

pair_id=?

ID of the HyperMetro pair.

Run the "show hyper_metro_pair general" command to obtain the value.

Level

Guest

Usage Guidelines

None

Example

  • To query all HyperMetro pairs in the device, run the following command.
    admin:/>show hyper_metro_pair general 
    ID Health Status Running Status Domain Name Type Size Role Local Name Remote Name 
    ---------------- ------------- -------------- ------ ----- ------------ ------------------ - -------------------- -------- 
    200bc79b99520000 Normal Normal HCD001 LUN 100.000GB Preferred LUN001 extLun001 
    200bc79b99520002 Normal Normal HCD002 FS 10.000GB Non-preferred FS001 extFS001
  • To query HyperMetro pair "200bc79b99520000", run the following command.
    admin:/>show hyper_metro_pair general pair_id=200bc79b99520000 
    ID : 200bc79b99520000 
    Health Status : Normal 
    Running Status : Normal 
    Link Status : Linkup 
    Domain ID : 1 
    Domain Name : HCD001 
    Type : LUN 
    Size : 100.000GB 
    WWN : 200bc78945612300 
    IP(s) : -- 
    Role : Preferred 
    Local ID : 5 
    Local Name : LUN005 
    Local Data Status : Consistent 
    Local Access Status : Read And Write 
    Remote ID : 5 
    Remote Name : extLUN005 
    Remote Data Status : Consistent 
    Remote Access Status : Read And Write 
    Recovery Policy : Automatic 
    Sync Progress(%) : -- 
    Sync Direction : -- 
    Sync Rate : Middle 
    Start Time : 2013-12-22/17:18:32 UTC+08:00 
    End Time : 2013-12-22/17:18:32 UTC+08:00 
    Consistency Group ID : 1 
    Consistency Group Name : cg001 
    Isolation Switch        : Close                            
    Isolation Threshold(ms) : 1000 
    Lock Mode  : Optimistic Mode 
    Time Remaining for Synchronization : --

System Response

The following table describes the parameter meanings.

Parameter

Meaning

ID

ID of the HyperMetro pair,64bits.

Health Status

Health status: Normal or Fault.

Running Status

Running status: Normal, Synchronizing, To Be Synchronized, Pause, Forced Start or Invalid.

Link Status

Link status: Linkup or Linkdown.

Domain ID

ID of the HyperMetro domain.

Domain Name

Name of the HyperMetro domain.

Type

Resource type: LUN or FS.

Size

Resource size.

WWN

LUN WWN.

IP(s)

IP address of the FS share service.

Role

Primary or Secondary/Preferred or Non-preferred. A/P indicates active/passive, and A/A indicates arbitration is required.

Local ID

ID of the local resource.

Local Name

Name of the local resource.

Local Data Status

Local data status: Consistent or Inconsistent.

Local Access Status

Local host access status: No Access or Read and Write.

Remote ID

ID of the remote resource.

Remote Name

Name of the remote resource.

Remote Data Status

Remote data status:Consistent or Inconsistent.

Remote Access Status

Remote host access status: No Access, Read Only or Read and Write.

Recovery Policy

Recovery policy: Automatic or Manual.

Sync Progress(%)

Synchronization progress (%): 0 to 100 (valid for LUNs only).

Sync Direction

Synchronization direction: Local to Remote or Remote to Local.

Sync Rate

Synchronization rate: Highest, High, Middle, Low.

Start Time

Start time of the last synchronization.

End Time

End time of the last synchronization.

Consistency Group ID

CG ID.

Consistency Group Name

CG name.

Isolation Switch

Isolation switch: open or close.

Isolation Threshold(ms)

Isolation threshold.

Lock Mode

The lock mode of hypermetro pair: Optimistic Mode or Pessimistic Mode.

Time Remaining for Synchronization

Time Remaining for Synchronization.

Translation
Download
Updated: 2019-07-16

Document ID: EDOC1100049140

Views: 121320

Downloads: 149

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next