No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

Command Reference for Block

OceanStor Dorado V3 Series V300R002

This document is applicable to OceanStor Dorado3000 V3, Dorado5000 V3, Dorado6000 V3 and Dorado18000 V3. Based on the CLI provided by the DeviceManager, this document describes how to use various commands classified by functions and how to set the CLI and manage the storage system through these commands.
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
add bond_port ipv6_route

add bond_port ipv6_route

Function

The add bond_port ipv6_route command is used to add an IPv6 route to the bond port. You can run this command to add a route to connect the storage system to the application server when their IPv6 addresses are not at the same network segment.

Format

add bond_port ipv6_route bond_port_name=? type=? [ target_ip=? ] [ prefix_length=? ] gateway=?

Parameters

Parameter

Description

Value

bond_port_name=?

Bond port name.

To obtain the value, run the "show bond_port" command.

type=?

Specified route type.

The value can be "net", "host", or "default", where:

  • "net": route to the target network segment.
  • "host": route to the target application server.
  • "default": default route. If the target network segment or application server is not in any route, you can use this default route to access.

target_ip=?

IPv6 address of the network segment at which the application server is. This parameter is valid when "type=?" is "net" or "host".

The value can be, for example, "1118::0".

prefix_length=?

Prefix length of the application server's IPv6 address. This parameter is valid when "type=?" is "net".

The value can be a number ranging from 1 to 128.

gateway=?

IPv6 address of the gateway of the host bond port.

-

Level

Administrator

Usage Guidelines

  • Before running the "add bond_port ipv6_route" command to add a route, you need to ensure that an IP address has been configured for the bond port.
  • Running the "add bond_port ipv6_route bond_port_name=? type=net target_ip=? prefix_length=? gateway=?" command adds a route to the target network segment.
  • Running the "add bond_port ipv6_route bond_port_name=? type=host target_ip=? gateway=?" command adds a route to the target application server.
  • Running the "add bond_port ipv6_route bond_port_name=? type=default gateway=?" command adds the default route.

Example

Add an IPv6 route for a bond port whose name is "bond_1_1", IP address at the target network segment is "1118::0", prefix length is "32", and IP address of the gateway is "2100::1". The bond port name and command output vary depending on products. The name and output here are just examples.

admin:/>add bond_port ipv6_route bond_port_name=bond_1_1 type=net target_ip=1118::0 prefix_length=32 gateway=2100::1 
DANGER: You are about to change the route of port. If the route is unavailable, this operation will disconnect the storage system from hosts. 
Suggestion: Before performing this operation, ensure that the entered route is available. 
Have you read danger alert message carefully?(y/n)y 
Are you sure you really want to perform the operation?(y/n) 
Command executed successfully.

System Response

None

Translation
Download
Updated: 2019-07-16

Document ID: EDOC1100049140

Views: 122872

Downloads: 153

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next