No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

FusionStorage OBS 7.0 Hardware Installation Guide 07

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
TaiShan 200 (Model 2280) 12-Slot Node

TaiShan 200 (Model 2280) 12-Slot Node

This section describes the function, appearance, ports, indicators, physical structure, and technical specifications of a TaiShan 200 (Model 2280) 12-slot node.

Function

A TaiShan 200 (Model 2280) 12-slot node is a 2 U dual-socket rack server developed based on Huawei Kunpeng 920 processor. It is applicable to Internet, distributed storage, cloud computing, big data, and enterprise services, and features high-performance computing, large-capacity storage, low power consumption, easy management, and easy deployment.

TaiShan 200 (Model 2280) 12-slot nodes are applicable to FusionStorage OBS 7.0.1 and later versions.

Appearance

Entire device

Figure 14-39 shows the appearance of the node.
Figure 14-39 Appearance

Front view

Figure 14-40 shows the front panel of the node.

Figure 14-40 Front panel

1

UID button/indicator

2

Health status indicator

3

Power button/indicator

4

Fault diagnosis LED

5

Flexible NIC indicators (1 and 2)

6

Service disk

7

Disk fault indicator

8

Disk activity indicator

9

VGA port

10

USB 3.0 port

11

Label plate with an ESN label

-

-

The front panel of the node provides 12 service disk slots numbered 0 to 11 from top to bottom and from left to right, as shown in Figure 14-41.

Figure 14-41 Disk slots on the front panel of the node

Rear view

Figure 14-42 shows the rear panel of the node.

Figure 14-42 Rear panel

1

I/O module 1

2

I/O module 2

3

I/O module 3

4

Power module indicator

5

Power module 2

6

Power module 1

7

Connection status indicator/Data transmission status indicator for an optical port

8

Data transmission rate indicator for an optical port

9

Flexible NIC 2

10

UID indicator

11

USB 3.0 port

12

VGA port

13

Serial port

14

Connection status indicator for the management network port

15

Management network port

16

Data transmission status indicator for the management network port

17

Connection status indicator for a GE electrical port

18

Data transmission status indicator for a GE electrical port

19

Flexible NIC 1

-

-

Ports

Table 14-21 and Table 14-22 show ports provided by the node.

Table 14-21 Ports on the front panel

Port

Type

Quantity

Description

USB port

USB 3.0

2

Connects to a USB device.

NOTICE:

Before connecting to a USB device, ensure that the USB device operates properly. A node may operate abnormally if it is connected to a faulty USB device.

Table 14-22 Ports on the rear panel

Port

Type

Quantity

Description

Power module socket

-

2

Connects to a power supply.

GE electrical port

RJ-45

4/8

The mainboard provides GE electrical ports. A maximum of eight GE electrical ports can be provided through two flexible NICs.

25GE optical port

SFP+

4/8

The mainboard provides 25GE optical ports. A maximum of eight 25GE optical ports can be provided through two flexible NICs.

NOTE:

25GE optical ports support 10GE autonegotiation through optical modules with different rates.

USB port

USB 3.0

2

Connects to a USB device.

NOTE:

Before connecting to a USB device, ensure that the USB device operates properly. A node may operate abnormally if it is connected to a faulty USB device.

Management network port

RJ-45

1

Functions as a 1000 Mbit/s Ethernet port, used for node management.

VGA port

DB-15

1

Connects to a terminal, such as a monitor or KVM.

Serial port

RJ-45

1

Functions as the system serial port by default. You can set it as the iBMC serial port by using the iBMC command. This port is used for debugging.

Indicators

You can initially determine the operating status of the node by observing its indicators.

Table 14-23 shows the indicators and buttons on the front panel of the node.

Table 14-23 Indicators and buttons on the front panel

Silkscreen

Description

Status

Fault diagnosis LED

  • ---: The node is operating properly.
  • Error code: A fault occurs in node hardware.
  • For details about error codes, see Rack Server iBMC Alarm Handling. Obtain the document as follows:

    Log in to https://support.huawei.com/enterprise, enter server model TS200-2280 in the search box, and click the associated path that is displayed. The corresponding product page is displayed. Click Documentation, and search for and download the document of the desired version.

Health status indicator

  • Steady green: The node is operating properly.
  • Blinking red at 1 Hz: A major alarm is generated.
  • Blinking red at 5 Hz: A critical alarm is generated.

UID button/indicator

The UID button/indicator helps identify and locate a node. You can turn on or off the UID indicator by pressing the UID button or remotely running a command on the CLI.

UID indicator:

  • Steady blue/Blinking blue: The node is located.
  • Off: The node is not located.

UID button:

  • To turn on or off the UID indicator, press this button.
  • To reset iBMC, hold down the UID button for 4 to 6 seconds.

Power button/indicator

Power indicator:

  • Steady yellow: The node is ready to be powered on.
  • Steady green: The node is properly powered on.
  • Blinking yellow: iBMC is starting.
  • Off: The node is not powered on.

Power button:

  • When the node is powered on, you can press this button to shut down the OS.
  • When the node is powered on, you can hold down the button for 6 seconds to forcibly power it off.
  • When the node is ready to be powered on, you can press this button to power it on.

NMI button

The NMI button triggers a node to generate a non-maskable interrupt (NMI). To generate an NMI, press this button or click the button on the iBMC WebUI.

NOTE:
  • The NMI button is used when the OS cannot be used. Do not use this button when the node is running properly.
  • The NMI button is used only for internal commissioning. When using the NMI button, ensure that there is a corresponding NMI interruption processing program in the OS. Otherwise, the system may break down. Use the button with caution.

Connection status indicator for a network port

Each indicator shows the status of an Ethernet LAN on motherboard (LOM) port.

  • Steady green: The network port is properly connected.
  • Off: The network port is not in use or has failed.
NOTE:

The indicators show the status of the two 10GE and two GE LOM ports.

Table 14-24 shows the indicators and buttons on the rear panel of the node.

Table 14-24 Indicators on the rear panel

Indicator

Status

25GE optical port

Data transmission rate indicator

  • Steady green: The data transmission rate is 25 Gbit/s.
  • Steady yellow: The data transmission rate is not 25 Gbit/s.
  • Off: The network is not connected.

Connection status indicator/Data transmission status indicator

  • Steady green: The network is properly connected.
  • Blinking green: Data is being transmitted.
  • Off: The network is not connected.

GE electrical port

Connection status indicator

  • Steady green: The network is properly connected.
  • Off: The network is not connected.

Data transmission status indicator

  • Blinking yellow: Data is being transmitted.
  • Off: No data is being transmitted.

UID indicator

The UID indicator helps identify and locate a node. You can turn on or off the UID indicator by pressing the UID button or remotely running a command on the iBMC CLI.

  • Steady blue/Blinking blue: The node is located.
  • Off: The node is not located.

Power module indicator

  • Steady green: The power input and output are normal.
  • Steady orange: The input is normal, but no power output is supplied due to overheat protection, overcurrent protection, short circuit protection, output overvoltage protection, or some component failures.
  • Blinking green at 1 Hz:
    • The input is normal, the node is standby, and the power module is in MV6 mode. (The output voltage is 6.7 V.)
    • The input is overvoltage or undervoltage.
    • The power module is in deep hibernation mode.
  • Blinking green at 4 Hz: under online firmware upgrade.
  • Off: No AC power is supplied.

Physical Structure

Figure 14-43 shows components of the node.

Figure 14-43 Components

1

I/O module 1

2

I/O module 2

3

Power module

4

Chassis

5

I/O module 3

6

Air duct

7

Front-disk backplane

8

Fan module bracket

9

Fan module

10

Front disks

11

Cable organizer

12

Heat sink

13

DIMM

14

Mainboard

15

Flexible NIC

16

iBMC card

Technical Specifications

Table 14-25 lists the technical specifications of a TaiShan 200 (Model 2280) 12-slot node.

Table 14-25 Technical specifications

Category

Item

Specifications

Physical specifications

Dimensions (H x W x D)

86.1 mm (2 U, 1 U = 44.45 mm) x 447 mm x 790 mm

Weight

  • Net weight: 32 kg
  • Weight of packing materials: 5 kg

Environmental specifications

Operating temperature

5°C to 45°C

Operating humidity

8% RH to 90% RH

Power specifications

220 V AC and 240 V high-voltage DC (adaptive)

  • AC: 200 V AC to 240 V AC (50 Hz/60 Hz)
  • High voltage DC: 192 V DC to 288 V DC

Power consumption specifications

Max. power consumption

750 W

Translation
Download
Updated: 2020-01-03

Document ID: EDOC1100051333

Views: 24194

Downloads: 29

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Share
Previous Next