No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search


To have a better experience, please upgrade your IE browser.


FusionStorage OBS 7.0 Hardware Installation Guide 07

Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Installing a TaiShan 200 (Model 2280) 12-Slot Node

Installing a TaiShan 200 (Model 2280) 12-Slot Node

Installing a TaiShan 200 (Model 2280) 12-slot node into the cabinet includes sliding the node into the cabinet, fastening the node, and checking the installation.


  • Operations described in Installing a Huawei Cabinet or Checking a Third-Party Cabinet have been completed.
  • Holding rails have been installed.
  • All required tools have been prepared, including M3 to M6 Phillips screwdrivers, M6 screws, and protective gloves.
  • The CPU, DIMM, riser card, PCIe card on the riser card, PCIe card, and built-in disks (optional) of the node have been installed. If any of the parts is not installed, see section Replacing Parts of a TaiShan 200 (Model 2280) 12-Slot Node in Parts Replacement to install it.


TaiShan 200 (Model 2280) 12-slot nodes are applicable to FusionStorage OBS 7.0.1 and later versions.

  • A fully configured TaiShan 200 (Model 2280) 12-slot node weighs up to 30 kg. Arrange for at least two persons to carry it and ensure that they wear protective gloves to avoid personal injury.
  • Install components into a cabinet from bottom to top to prevent the cabinet from falling over.


  1. Install the node.

    1. Pull out the inner rails as far as they will go. See Figure 8-29.
      Figure 8-29 Pulling out an inner rail
    1. Align the screws on the node with the notches on the inner rails, push the node inwards until you hear a sound, and ensure that the latches eject and completely block the screws to affix the node to the inner rails. See Figure 8-30.
      Figure 8-30 Attaching the node to the rails
    2. Press the release buttons on both sides and push the node into the cabinet along the holding rails. See Figure 8-31.
      Figure 8-31 Pushing the node into a cabinet along the holding rails
    1. (Optional) Tighten the captive screws on the mounting ears to secure the node. See Figure 8-32.
      Figure 8-32 Securing the node

  2. Install the cable organizer.

    1. Insert the support lever into both left and right outer rails. See step 1 in Figure 8-33.
    2. Insert the nail heads on the outer left rail into the holes on the outer support lever of the cable organizer, and pull the cable organizer out to secure it. See step 2 in Figure 8-33.
    3. Insert the nail heads on the inner left rail into the holes on the inner support lever of the cable organizer, and pull the cable organizer out to secure it. See step 3 in Figure 8-33.
      Figure 8-33 Installing a cable organizer

  3. Optional: Install front disks.

    1. Fully raise the ejector lever and push a disk into the chassis along the guide rails until it does not move. See step 1 in Figure 8-34.

    To ensure favorable heat dissipation, insert disks in the sequence of disk slot numbers. If disk modules or PCIe cards are not fully configured, install filler panels into vacant disk or PCIe slots.

    Figure 8-34 Installing a front disk
    1. Ensure that the ejector lever is fastened to the chassis beam, and lower the ejector lever to completely insert the disk into the chassis. See step 2 in Figure 8-34.

Updated: 2020-01-03

Document ID: EDOC1100051333

Views: 24297

Downloads: 29

Average rating:
This Document Applies to these Products

Related Version

Related Documents

Previous Next