No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Verifying the IPv6 PIM-SSM Configuration

Verifying the IPv6 PIM-SSM Configuration

After configuring IPv6 Protocol Independent Multicast-Source-Specific Multicast (PIM-SSM), verify PIM interfaces, PIM neighbors, and PIM routing tables by using related commands.

Prerequisites

The IPv6 PIM-SSM configurations are complete.

Procedure

  • Run the display pim ipv6 interface [ interface-type interface-number ] [ verbose ] command to check IPv6 PIM interfaces.
  • Run the display pim ipv6 neighbor [ ipv6-link-local-address | interface interface-type interface-number | verbose ] * command to check IPv6 PIM neighbors.
  • Run the display pim ipv6 routing-table [ ipv6-source-address [ mask mask-length ] | ipv6-group-address [ mask mask-length ] | incoming-interface { interface-type interface-number | register } | outgoing-interface { include | exclude | match } { interface-type interface-number | register | none } | mode { sm | ssm } | flags flag-value | fsm ] * [ outgoing-interface-number [ number ] ] command to check the IPv6 PIM routing table of a device.

Example

Run the display pim ipv6 interface command. You can view the number of PIM neighbors on each interface and see that the PIM status is Up on each interface.

<HUAWEI> display pim ipv6 interface
VPN-Instance: public net
 Interface           State NbrCnt HelloInt   DR-Pri     DR-Address
 GE1/0/0             up    1      30         1          FE80:1::3456

Run the display pim ipv6 neighbor command. You can view the number of PIM neighbors, neighbor addresses, and interfaces that set up neighbor relationships.

<HUAWEI> display pim ipv6 neighbor
 VPN-Instance: public net
 Total Number of Neighbors
= 1 

 Neighbor        Interface           Uptime   Expires  Dr-Priority  BFD-Session 
 FE80:1::3456    GE1/0/0             00:01:08 never    1            N

Run the display pim ipv6 routing-table command. You can view the source addresses, group addresses in PIM entries, upstream interfaces, and downstream interface lists of PIM entries.

<HUAWEI> display pim ipv6 routing-table
VPN-Instance: public net
 Total 0 (*, G) entry; 2 (S, G) entries
 
 (2001:db8:1::1, FF06::)
     RP: NULL
     Protocol: pim-sm, Flag: SPT NIIF SG_RCVR 
     UpTime: 00:00:14     
     Upstream interface: NULL
         Upstream neighbor: NULL         
         RPF prime neighbor: NULL         
         Join/Prune FSM: [SPT: NJ] [RPT: NJ] 
     Downstream interface(s) information: none
 
 (2001:db8:1::2, FF06::)
     RP: NULL
     Protocol: pim-sm, Flag: SPT NIIF SG_RCVR 
     UpTime: 00:00:14     
     Upstream interface: NULL
         Upstream neighbor: NULL         
         RPF prime neighbor: NULL         
         Join/Prune FSM: [SPT: NJ] [RPT: NJ] 
     Downstream interface(s) information: none
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 43480

Downloads: 97

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next