No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IPv6 Static Multicast

Configuring IPv6 Static Multicast

To allow IPv6 BAS users to receive the traffic of specific multicast groups without sending MLD join messages, configure static multicast.

Usage Scenario

Configure static multicast when a program (such as an advertisement program) needs to be pushed to users, delivered to users' STBs before users join the program, or delivered to Layer 2 devices before users join the program. Static multicast helps shorten the program switching duration.

Pre-configuration Tasks

Before configuring static multicast, complete the tasks shown in Figure 15-3. For configuration details, see Table 15-2.

Figure 15-3 Pre-configuration tasks for static multicast configurations
Table 15-2 Pre-configuration tasks

Task

Link

Configure an IPv6 address pool to assign IPv6 addresses to access users.

Configure AAA authentication and accounting schemes.

Configure a domain to implement AAA functions and manage access users.

Configure the PPPoE or IPoE access mode.

  • Configuring the PPPoXv6 Access Service

  • Configuring the IPoEv6 Access Service

Enable multicast routing, PIM, and MLD.

  1. Enable IPv6 multicast routing

  2. Enable IPv6 PIM-SM

  3. Enable MLD

Configure a BAS interface.

Procedure

  1. Configure an IPv6 static multicast program list.
    1. Run system-view

      The system view is displayed.

    2. Run aaa

      The AAA view is displayed.

    3. Run multicast-list ipv6 list-name [ index list-index ] [ source-ipv6-address source-ipv6-address [ source-ipv6-prefix-length ] ] group-ipv6-address group-ipv6-address [ group-ipv6-prefix-length ] [ vpn-instance vpn-instance-name ]

      An IPv6 multicast program list is configured.

  2. Configure an IPv6 multicast profile.
    1. Run system-view

      The system view is displayed.

    2. Run aaa

      The AAA view is displayed.

    3. Run multicast-profile ipv6 profile-name

      An IPv6 multicast profile is created, and the profile view is displayed.

    4. Run multicast-list ipv6 { name list-name | list-index start-index [ end-index ] } [ static]

      The IPv6 multicast program list is bound to the IPv6 multicast profile.

    5. Run authentication

      Authentication is enabled for IPv6 multicast users.

  3. Bind the multicast profile to the AAA domain.
    1. Run system-view

      The system view is displayed.

    2. Run aaa

      The AAA view is displayed.

    3. Run domain domain-name

      The AAA domain view is displayed.

    4. Run multicast-profile [ ipv6 ] profile-name

      The IPv6 multicast profile is bound to the AAA domain.

    After a multicast profile is bound to a domain, users in this domain are allowed to access the programs defined in the multicast program list that is bound to the multicast profile. One domain can use only one multicast profile. If multiple multicast profiles are bound to a domain, the latest binding takes effect.

Checking the Configurations

Run the display multicast-profile ipv6 command to check information about a specified or all IPv6 multicast profiles.

# Check information about all multicast profiles.
<HUAWEI> display multicast-profile ipv6
---------------------------------------------------------------------
Index      Multicast-profile-name-ipv6                 IfAuthentic
---------------------------------------------------------------------
    0      name1                                       Yes
    1      name2                                       Yes
---------------------------------------------------------------------
Total: 2
# Check multicast IPv6 program lists bound to a specified multicast profile.
<HUAWEI> display multicast-profile ipv6 name1
 Profile-name-ipv6                   : name1
 If-authentic                        : Yes
 Static multicast-list-name-ipv6     : listname1
 Static multicast-list-name-ipv6     : listname2

Run the display multicast-list ipv6 command to check information about a specified or all IPv6 multicast program lists.

# Check information about all IPv6 multicast program lists.

<HUAWEI> display multicast-list ipv6
Total: 2
---------------------------------------------------------------------
Multicast-list ipv6 name : listname1
Index                    : 0 
Source IPv6/prefix       : FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF/128 
Group IPv6/prefix        : FF1E::1/128 
Multicast-list ipv6 name : listname2 
Index                    : 1 
Source IPv6/prefix       : FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF/128 
Group IPv6/prefix        : FF1E::2/128 
---------------------------------------------------------------------

# Check information about a specified IPv6 multicast program list.

<HUAWEI> display multicast-list ipv6 listname1
---------------------------------------------------------------------
Multicast-list ipv6 name  : listname1
Index                     : 0
Source IPv6/prefix        : FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF/128 
Group IPv6/prefix         : FF1E::1/128 
---------------------------------------------------------------------
Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 44055

Downloads: 97

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next