No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
Configuring IPv6 SSM Mapping

Configuring IPv6 SSM Mapping

Some hosts can run only MLDv1. To enable such hosts to obtain the MLDv2 service, configure SSM mapping.

Context

Compared to the traditional any-source multicast (ASM) technology, source-specific multicast (SSM) can conserve multicast addresses and has higher security, but MLDv2 only supports SSM. The majority of the latest multicast devices support MLDv2, but most legacy multicast terminals only support MLDv1 and hope to enjoy the MLDv2 multicast service. SSM mapping enables the compatibility in the SSM range by supporting hosts running MLDv1.

SSM mapping enables a Layer 2 device to map (*, G) information in MLDv1 data messages to (S, G) information in MLDv2 data messages. This allows hosts running MLDv1 to receive multicast data from an upstream Layer 3 device running MLDv2.

If a user joins a multicast group in the ASM range but wants to enjoy the SSM service of the multicast group, add the multicast group address to an SSM policy, and then configure SSM mapping.

Procedure

  1. Run system-view

    The system view is displayed.

  2. Run acl { number basic-acl-number | name acl-name }

    The ACL view is displayed.

  3. Run rule permit source source-ip-address source-wildcard

    A basic ACL rule is configured.

  4. (Optional) Run rule deny source any

    The device is configured to process other multicast group addresses as ASM ones.

    NOTE:

    Set permit in the rule command. Otherwise, the SSM group range configuration does not take effect. If you set deny or the specified address is not a multicast address, the configuration does not take effect either.

  5. Run quit

    Return to the system view.

  6. Perform either of the following operations based on the VLAN or VPLS networking scenario:

    • Run the vlan vlan-id command to enter the VLAN view.
    • Run the vsi vsi-name [ static ] command to enter the VSI view.

  7. Run mld-snooping enable

    MLD snooping is enabled for the VLAN/VSI.

  8. Run mld-snooping version 2

    MLDv2 is set as the version of MLD snooping.

  9. Run mld-snooping ssm-policy { basic-acl6-number | acl6-name acl6-name }

    The specified multicast address is added to the SSM group address range.

  10. Run mld-snooping ssm-mapping enable policy policy-name

    SSM mapping is enabled for the VLAN/VSI.

  11. Run mld-snooping ssm-mapping ip-group-address { ip-group-mask | mask-length } ip-source-address

    The multicast address in the specified range is mapped to a specified source address.

    The specified multicast address is in the SSM address range.

  12. Run commit

    The configuration is committed.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 39521

Downloads: 97

Average rating:
This Document Applies to these Products
Related Documents
Related Version
Share
Previous Next