No relevant resource is found in the selected language.

This site uses cookies. By continuing to browse the site you are agreeing to our use of cookies. Read our privacy policy>Search

Reminder

To have a better experience, please upgrade your IE browser.

upgrade

NE40E V800R010C10SPC500 Configuration Guide - IP Multicast 01

This is NE40E V800R010C10SPC500 Configuration Guide - IP Multicast
Rate and give feedback:
Huawei uses machine translation combined with human proofreading to translate this document to different languages in order to help you better understand the content of this document. Note: Even the most advanced machine translation cannot match the quality of professional translators. Huawei shall not bear any responsibility for translation accuracy and it is recommended that you refer to the English document (a link for which has been provided).
(Optional) Adjusting Source Registration Parameters

(Optional) Adjusting Source Registration Parameters

A new multicast source must register with a Rendezvous Point (RP). You can configure policies of filtering Register messages on the Candidate-Rendezvous Points (C-RPs) and set the holdtime of the register-suppression state and the interval for sending null Register messages on the source's DR or disable the source's DR from sending Register messages.

Context

On an IPv6 PIM-SM network, the source's Designated router (DR) encapsulates multicast data into a Register message and sends the message to the RPs in unicast mode. The RP then decapsulates the message and forwards the extracted multicast data to receivers along the rendezvous point tree (RPT). To prevent the attack of invalid Register messages, you can configure the RP to accept or deny the Register messages matching specified rules.

After the RP completes the shortest path tree (SPT) switchover, the IPv6 multicast data reaches the RP along the source tress in multicast mode. The RP then sends a Register-Stop message to the source's DR. After receiving the message, the source's DR stops sending Register messages and enters the suppression state. In the register suppression period, the DR periodically sends a probe messages (null Register message) to notify the RP that the multicast source is still in the active state. After the register suppression period expires, the DR resends the Register messages carrying multicast data.

The router can work normally with default control parameters. You are allowed to adjust registration parameters based on the specific networking environment.

NOTE:

If there is no special requirement, default parameter values are recommended.

Procedure

  • Control the receiving of Register messages on a C-RP.
    1. Run system-view

      The system view is displayed.

    2. Run acl ipv6 { name advance-acl6-name [ advance | [ advance ] number advance-acl6-number ] | [ number ] advance-acl6-number } [ match-order { config | auto } ]

      An advanced ACL6 is created, and the advanced ACL6 view is displayed.

    3. Run rule [ rule-id ] [ name rule-name ] { deny | permit } ipv6 [ destination { destination-ipv6-address prefix-length | destination-ipv6-address/prefix-length | any } | source { source-ipv6-address prefix-length | source-ipv6-address/prefix-length | any } ] *

      Rules are configured for the advanced ACL6.

      Run the rule command, set the source parameter to a multicast source address, and set the destination parameter to a multicast group address.

    4. Run quit

      Return to the system view.

    5. Run pim-ipv6

      The IPv6 PIM view is displayed.

    6. Run register-policy { advanced-acl6-number | acl6-name acl6-name }

      A policy is configured to filter Register messages.

      NOTE:
      • If a Register message matches an ACL rule and the action is permit, the RP permits this message.
      • If a Register message matches an ACL rule and the action is deny, the RP denies this message.
      • If a Register message does not match any ACL rule, the RP denies this message.
      • If a specified ACL does not exist or does not contain rules, the RP denies all Register messages.

    7. Run commit

      The configuration is committed.

  • Suppress multicast source registration on the source's DR.
    1. Run system-view

      The system view is displayed.

    2. Run pim-ipv6

      The IPv6 PIM view is displayed.

    3. Run register-suppression-timeout interval

      The timeout period during which the source's DR keeps the register suppression state is set.

      • If the value of interval is small, the RP frequently receives burst multicast data.

      • If the value of interval is large, when an (S, G) entry on the RP times out, the delay during which new receivers join a multicast group is prolonged.

    4. Run probe-interval interval

      The interval for sending Probe messages is set.

    5. Run commit

      The configuration is committed.

Translation
Download
Updated: 2019-01-03

Document ID: EDOC1100055017

Views: 39845

Downloads: 97

Average rating:
This Document Applies to these Products
Related Version
Related Documents
Share
Previous Next